Re: ADV7619 color space conversion
OK, the script dump you attached does not output AVI infoframe from the 7511. Not a problem except the sink will always expect DVI - RGB mode. So with YCbCr input and INP_COLOR_SPACE = YCbCr 709 the...
View ArticleRe: Some questions about ADV212
Hello, Blanking is required. Without blanking, this will not work. I would use at least 6 lines between frames and 10 pixels of blanking per line. Why DCS mode instead of normal burst DMA? Dave
View ArticleClik here to view.
Re: ADF4110 locks too slow
The ADF4110 will start to lock the loop after a write to the AB counter latch. Your sequence should be something like this:Power up ADF4110 and VCO - VCO is output is some frequency between its output...
View ArticleWhat's the difference between the WSN development kits EV-ADRN-WSN-1Z and...
I went to Electronica trade fair in Munich last week and a guy at the AD stand showed me one of the above mentioned WSN development kits. On the AD website (Wireless Sensor Network (WSN) Development...
View ArticleRe: ADF4355-2 output range
Thanks, the app actually confirms that it works the way I was hoping it did. I appreciate the help!
View ArticleRe: adis 16364 gyro read problem
Yeah but how the 16381 value is translated since i do not rotate the imu.the number sequence in first post is for the same position of the imu.
View ArticleRe: Special Usage of HMC783LP6CE
Please refer to attached spreadsheet for configuration if using the HMC783LP6CE as a VCO. The part should be soldered down at all pin locations but the pins labeled NC can be left open. As an...
View ArticleRe: adis 16364 gyro read problem
Thank you for clarifying. There are a number of error sources that will prevent you from measuring a perfect zero with every sample, even though the device is not rotating. In fact, these behaviors,...
View ArticleClik here to view.
Re: HDCP issues with AppleTV (7612 as the Rx)
Hi Reshmi, Thanks for confirming the above behavior in your environment. I have logged this as a potential issue with the EVAL-ADV7612-7511 software driver. I'll let you know when I hear from the...
View ArticleClik here to view.
Re: AD8302 - Phase difference between two 2.4 GHz signals
Hi Matt, Below is TPC 29 on page 10 of the datasheet. This shows the VPHS output response (the triangular plot that references the "phase out -V" y-axis on the left and the phase error, in degrees,...
View ArticleRe: Question about High speed ADC
Hi,I know that all ADI ADCs that would support 200Msps over the last 15 years have had only positive supply voltages, and therefore positive, unipolar inputs ranges. And they are differential inputs...
View ArticleADIS16203 software error
Hi I am trying to evaluate the ADIS16203 with the ADISUSBZ board, my software seems to install fine (both of an XP-32 bit and Windows 7 32 bit machine). When I go to run the program I get a windows...
View ArticleRe: ADF4350 wrong output after warm-up
First suspicion is that the exposed paddle is not soldered properly to ground. Can you verify this? There should be a solid connection between the paddle and GND.
View ArticleRe: ADIS16203 software error
This sounds like the giveio.exe driver didn't install correctly or perhaps one of the USB support files didn't get to the right location. UG-363, page 7 has some details on...
View ArticleClik here to view.
Clik here to view.
Re: adis 16364 gyro read problem
Are you familiar with twos complement formats? Here is a picture of the table that I referenced in my first reply. Please note that -1 LSB, which is only one code lower than zero, is equal to 0x3FFF...
View ArticleRe: AD9467
Hi, Sorry, I am not a good reference on VHDL, so I can't help with that question. Regards, David
View ArticleClik here to view.
Re: ADF4350 wrong output after warm-up
Thanks for your reply. It is hard to check directly but I'm pretty sure it is okay, because: 1. this particular component was soldered with hot air and soldering paste (by hand), which makes it hard to...
View ArticleRe: ADU1446 sleep mode
I think there is a chicken and an egg situation here.The 144x is not inherently a low power parts. If you however use a ADAU1761, ADAU1781 or a SSM4329, then the power consumption for detecting audio...
View Article