ADV212 RAW and JDATA mode
Now,I am tring to use adv212 in Raw Video mode & JDATA mode controlled by FPGA After loading the firmware I check the SWAFLAG.It is FF82.Then I write 0xFFFF to EIRQFLG.VRDY becomes...
View ArticleRe: Some questions about ADV212
Hi Dave, There is a 8-bit gray-level raw image of 128 pixels X 128 pixels stored in a SRAM. All the pixels are active pixels. I use custom sepcific mode to put the image on VDATA by HVF signals as...
View ArticleRe: Reading of the actual Angle value of a ADIS16265 values does not fit
Hi, thanks for the quick answer. I just found the problem after taking a small break of the problem. uValue=((SPIReceiveBuffer[0] & 0x3F ) << 8) +...
View ArticleRe: AD-FMCMOTCON1-EBZ MathWorks FOC IP controller will not go into closed...
When running the FOC IP in the IIO Scope the "Matlab Controller" option must be selected and the encoder must be plugged in. The regular controller runs only with the hall sensors. What do you mean by...
View Articleadsp-bf609-pixc-CCES
Greetings I am having problems understand the PIXC modes of operation, any tutorial or reference please - Work as LCD Driver, OGL, OCV, Blending on video I have blackfin @D Graphics Lib 4.1.0, put...
View ArticleClik here to view.
Re: using AD8067 as inverting amplifier
Hi Niloy, As i read through the datasheet (page 13), I found out the error in your circuit is the value for feedback resistor. 1kohm is recommended as feedback rather than 10kohm.In your case, you can...
View Articlebootng zynq zc702+fmcomms5
Hi , I erased my SD card and loaded the unzipped image in the Zynq quick start page using the win32diskimager application.I then followed the rest of the instructions, including the boot & tools...
View ArticleAD603 Data Sheet Circuit - Figure 49, page 18
Hello: I am making an amateur radio transceiver. I have based the IF strip of the receiver section of the transceiver on the circuit shown in the data sheet page 18 (figure 49). My circuit is as...
View ArticleClik here to view.
Re: Sigma300 (ADAU145x) Q&A
Hello, The Limiter block behaves similarly for me:Its "Flag" output is actually the Ratio output (thus is all over the place)Presumably, then, the "Ratio" output is the Flag -- but it's dead....
View ArticleClik here to view.
Re: AD9467
Thanks for a great answer, i think i was confused about the timing diagram on figure 2 on page 7 before, but i makes more sense now. One last question. The 2 output bits on each differential pair, do...
View ArticleRe: How can to achieve full scale ADC ?
Hello, using an amplifier stage in front of the AD7799 would in principle allow you to use the full scale of the ADC. But you have to be aware, that this only increases the nominal resolution (refered...
View ArticleRe: AD5560 multiple power rail measurement
Dear Sir/Madam, Thanks very much on your reply, as below I plot one diagram and try to explain our application in more insight, also we want to clarify the key items as below, 1. We power up...
View ArticleDid anyone came upon fake ADG3257 ?
Hi all, Lately, we had some failing ADG3257. Some worked few times and then failed, others failed right after assembly. They usually fail in only one of the switches. I would be less confused if they...
View ArticleRe: Can't compile Simulink model ad9361_sim.slx
Hi, I've attached two patch files that fix the compilation issue for running the simulink model on Linux platforms. Although gcc-4.7.2 was used to build the shared library binary, and the same version...
View ArticleADP225 UVLO Spec
Hello, I am using the ADP225ACPZ-R7 regulator, and I have noticed something strange with the feature "UVLO - falling edge": It says on the datasheet that the minimum voltage for shutdown is 2.2V, and...
View ArticleClik here to view.
Re: using AD8067 as inverting amplifier
Hi Jino, Thanks for your reply. I want to connect AD8067 with a sensor that has a resistance value around 12k ohm or even higher. Now input resistance of that high and feedback resistance 1k ohm, I...
View Articleadis 16364 gyro read problem
hello,i have an adis 16364 imu.when i read the product id everything works correctly.however,when i am trying to read the x_gyro_out for example the values i get are something...
View ArticleClik here to view.
Re: AD9361 sample rate in reference design
Hi DragosB First , I would like to thank you for your reply after which I am gradually able to understand the working . As you mentioned in your first reply to me the tx path frequencies are set in the...
View ArticleRe: ADV212 RAW and JDATA mode
Hello, One thing to keep in mind: You should NOT use raw pixel mode. It's very difficult to get working and it has many limitations. Please see the document on it on the design support files page for...
View Article