Re: AD8302 - Phase difference between two 2.4 GHz signals
Hi Matt, Usually on a receiver, isolation of a signal is done with filtering of some sort. You may be able to down-convert the signal and then measure phase, but I'm not familiar enough with that...
View ArticleClik here to view.
Re: HMC649 phase shift equation
Hi Rich, The HMC649/649LP6 is our 6-bit digital controlled phase shifter, integrated with 6 major phase shift states to provide 360deg of phase coverage with LSB of +5.625deg. The HMC649 will be in the...
View ArticleUpgrade to VisualDSP 5.1.1 from 5.0.10
Would there be any issue upgrading to 5.1.1 from 5.0.10 with a BF527? I cannot find any older release notes then 5.1.0. Does not look like there is any issues.
View ArticleRe: What is the AD equivalent part number to discontinued SSM2402...for Audio?
Hello Dave and Eric Thanks very much for replies!Eric...you say ADG5436.It could be very interesting but as you say it has no dip model of it.OK. If I would stick in using ±15V supplies only what...
View ArticleRe: ADE7912: conformity to IEC 61010-1 3rd Edition
Hi AP,We will certify the ADE7912 for IEC61010-1 3rd edition. The product was submitted and we are waiting for its certification.The product will be certified for Basic insulation, 300 Vrms maximum...
View ArticleClik here to view.
Re: AD9361 issues found (using FMCOMMS5 and IIO SCOPE) requiring explanation
Hi,I am still waiting for your answer to the question below : when signal is not centered it seems to be distorted/other.Thanks. Hi,Another question related to the 9361 samples captured via IIO...
View ArticleADuCM360 at high speed
I am using the ADuCM360 evaluation kit and not very up to speed but still wish to ask a question. I am tweaking the ADCMeter example and just streaming the data at 460800 baud. When I set the...
View ArticleRe: Questions Regarding ADE7880 Harmonics Calculations
Hi Karen, Those THD readings are very high, that basically means that most of your signal is in the harmonics rather than in the fundamental frequency. With the evaluation software, could you please...
View ArticleClik here to view.
Re: ADE7880 - Can't Get Correct Line Voltage Frequency
Hi Karen, Have you set the VLEVEL register? If so what value are you using? Could you please send me the register values for the three ANGLEx registers with the ANGLESEL bit in the 3 possible settings....
View ArticleNew JTAG Connections (10 pin)
Recently ADI started using a small 2x5 box header with 50mil pitch for JTAG. This connector is supported by the ICE-1000 & ICE-2000.The ICE-2000 has an adapter for the 2x7 legacy ADI JTAG header....
View ArticleRe: ADF4159 Eval Board FMCW
Please post a screenshot of the GUI. I presume one of the settings isn't set correctly.
View ArticleRe: Which IP cores are needed for building each HDL design in Vivado
Hi Rejeesh, I'm not sure how long it would take to do a grep on the whole of analog.com and I wouldn't have a clue what "regular expression" to search for, but then I'm not a Linux penguin. I have of...
View ArticleRe: CN0303 Support for EVAL-ADXL001-500GZ
Hi Mark, You are absolutely correct. Both the 250g and the 500g version will operate with the CN0303 board. The only thing that might not work out of the box would be the software, because there is a...
View ArticleRe: CN0303 Support for EVAL-ADXL001-500GZ
Thanks!Is that something that can be easily done? I suspect that if it was a big deal, manual re-scale wouldn't be that hard if the objective was peak resolution.
View ArticleHittite HMC1048 Mixer pinout
The Hittite HMC1048 mixer IC datasheet indicates pins 4 and 6 are N/C, although pin 5 = I/F output, which can reach several GHz of frequency. This seems very odd because adjacent pins on the other two...
View ArticleRe: adis 16364 gyro read problem
Just wanted to check back in on this. Does this make better sense now or are you still stuck? Thanks again for using the ADIS16364 and for posting in this forum.
View ArticleInterleaving the AD9234
Hi ADI, Is it possible to interleave the two ADCs on the AD9234 to achieve a higher sampling rate? Looking at the data sheet it looks like both parts are run from the same clock source, which suggests...
View ArticleRe: CN0303 Support for EVAL-ADXL001-500GZ
This shouldn't be to hard, but would require some time from the engineer who wrote the software. I'll see if I can get him to look at it and put in the option for the part variations. Brandon
View ArticleClik here to view.
DPG3 and AD9129-EBZ Evaluation Board Jitter
I am using the DPG3 and the AD9129-EBZ Evaluation Board to output different waveforms. I have the clock to the eval. board operating at 2.4GHz, and I am triggering the DPG3 with an external pulser....
View Article