Re: ADV7343 - Input Clock Frequency
Guenter, What about the control of ADV7611 output frequency by DR_STR_CLK[1:0], IO, Address 0x14[3:2] => 01 (Medium low (2×) for LLC up to 60 MHz). Or else Suggest the video encoder which supports...
View ArticleClik here to view.
Re: AD7656-1, how to keep holding sampled pairs
Hi, Sorry to push you anyhow, could you please provide any confirmation or point out any suspicious part ? I slightly refined chart attached before, which rectified part is red colored, so please see...
View ArticleRe: ADXL362 power consumption in wake-up mode with FIFO data storing
Hi Nikkee, In wake-up mode, no matter you enable FIFO or not, the power consumption is around 270nA. BRNeil
View ArticleRe: ADXL363 breakout board
Hi, So far, there is no breakout board for ADXL363. As it is pin-to-pin compatible with ADXL362 except the ADC input pin. You can try to buy EVAL-ADXL362Z-S, the socket on it can also hold ADXL363....
View ArticleRe: AD2S1210 Resolver to digital. Configuration
Hi Koldo, First of all, the LOS, DOS and DOS over-range fault detection mechanisms are based off the monitor signal. The monitor signal is a combination of both the sine and cosine signals. Please see...
View ArticleDoes ADV7182 have no problem when the SOC drives P[7:0] and LLC pins if TOD...
Hello,I have a question about Tristate Output Drivers of ADV7182.I think P[7:0], HS, VS/FIELD/SFL and LLC pins can be tri-stated (Hi-impedance) via TOD, Address 0x03[6] and TRI_LLC, Address 0x1D[7]....
View ArticleRe: AD7266 Data access time
Hi, yk. We are looking into this. I'll get back to you as soon as possible. Regards,Karen
View ArticleClik here to view.
Re: Can I use DC to input ADAS3023 for test?
Hi, Jason. It's the best practice to use RESET pulse to initialize the ADAS3023 after following the recommended power up sequence on page 24 in the datasheet. There is a description of RESET and PD...
View ArticleRe: Removing audio from HDMI(ADV7623)
Thanks for the update! I see from the ADV7623 scripts (ADV7623-Ver1-12Cust.txt), there is an ADI recommended write to IO map 0x1F:B2 1F 20 ; ADI Recommended Write I don't see any scripts that set this...
View ArticleRe: ADV7625 4K Video problem
Based on another thread, it seems you have 2.2.1EXP5 which is a very recent release of source code. If you have a question about the schedule for source code release, it would probably be best to...
View ArticleClik here to view.
Re: AD637 Scale Factor Trim
Hello Jim, 1) Is resistor R4 in the circuit permanently, or only switched in while adjusting R3? Yes, R4 is permanently part of the circuit. The R3 pot slightly attenuates the denominator...
View ArticleRe: ADV7611 outputs Black video after plugging HDMI cable and it does not...
Hi Adrián, If you can't reproduce the issue on our evaluation board, then it definitely points to software differences. Do you see this same behavior when running our recommended scripts for ADV7612...
View ArticleRe: Re: AD8302 and AD9834
Hi Joel,I am providing one reference input (inp B) to AD8302 from DDS (AD9834) at 10 MHz frequency and the other through DUT (input A). When I was checking the inputs at AD8302 through CRO, then input...
View ArticleRe: Output offset with AD620
Hi Peter, Thanks for using ADI products on your applications. Where is your input voltage coming from? Can you make sure that it is not floating by ensuring the it is connected to a common ground where...
View ArticleRe: ADL5304 usable range
Hi Peter, I moved your question about the ADL5304 in the RF Community. Someone here should be able to assist you. Best regards,Emman
View ArticleReference input AD5686R
What is refference current,, input range and input Impedance for VRef in if is used as input for externa reference voltage?In addition toconsidering the use ofinternal andexternal referenceconnected...
View ArticleClik here to view.
Re: Noise AD9822
I just take the CCD out of the circuit and I still have noise on the digital part, ThanksMajid
View ArticleRe: Standard digital isolator for I2S audio line
Hi MSCantrell, Thank you very much for your reply and concerning. At first for your question, target performance is 5~6 Mbps in current design, however it may increase to around 20 Mbps in near future...
View Article