Re: ADF4351 settling time calculation using teh EVAL baords
Thanks,That seems to decrease the time. However, I have noticed the following:I set up the scan from 1000 MHz to 2000 Hz in steps of 1 MHz. And I have noticed that the lock time is not the same but the...
View ArticleRe: Can we make ADV7626 just pass the AV mute ON to sink without sending...
Hello Matt, Sorry for the delay, I was working on some other issues in the past days. Yes, I saw this behavior on EVA-ADV7625-SMZ as well, the software driver was enabled. If you connect two EVA...
View ArticleClik here to view.
Re: BF609 uClinux booting fails
Hi Aaronwu, I did not change any source code and any configuration files. > make bf609-ezkit_defconfig> make munuconfigI checked two options, IPv6 and WCHAR support. When they are unchecke,...
View ArticleClik here to view.
Maximizing efficiency at 5 mA while using ADuM3070
Hi, ADuM3070 datasheet contains following efficiency graph:I plan to use 5V input voltage and 3.7V output voltage with 5mA maximum (1.5mA typical) load current. I would like to create effective...
View ArticleClik here to view.
Re: BF609 uClinux booting fails
Hi Andre, Yes, I am building from the default bf609-ezkit_defconfig. I checked two options from menuconfig.IPv6 support and WCHAR support. Without those checking, I encounter errors while compiling. My...
View ArticleRe: Clocks for ADAU1701 and Codec CS4272
Hi Johannes, The divide down value is based on the internal core clock freqency of 49.152 MHz, not the 12.288 MHz MCLK input. A divide by 16 should generate 3 MHz clock (49.152 MHz/16 = 3.072 MHz)....
View ArticleClik here to view.
Re: FMCOMMS1: Clock Genarator adjustments...
Hi Ehsan, I also think that its fair to single out the AD9523-1 at this point. Since you are using a PLL1 feedback divider of 4 with both the 122.88MHz and 80MHz VCXO, can you run the standard driver...
View ArticleRe: Question on Programming AD9837 on EVAL board
Hi Mike,You have asked your question in the place where people learn to use EngineerZone. This is not a product support community. Please repost your question to the appropriate product support...
View ArticleRe: How to use biquad function correctly?
Hi Graydon,You have asked your question in the place where people learn to use EngineerZone. This is not a product support community. Please repost your question to the appropriate product support...
View ArticleRe: adv7611 don`t start
Hi Alexandr,You have asked your question in the place where people learn to use EngineerZone. This is not a product support community. Please repost your question to the appropriate product support...
View ArticleRe: how to download the datasheet in your web
HI Xiao,Please navigate to http://www.analog.com, type in the product number you are looking for and then click on the PDF Data Sheet symbol to down load.Thank you,Lisa
View ArticleClik here to view.
Re: ADF4351 settling time calculation using teh EVAL baords
This is the sweep function that is currently in the ADF4351 software:In the example above, the step size is 1 MHz. If you explain what you want, I can build it into the software. Is it that you define...
View ArticleClik here to view.
adv7611 don`t start
Hello. I have EVAL-ADV7611EBZ and try to work with it.i have 2 situation.1) When i use standart script it work fine - it`s ok 2) I try to connect microcontroller by i2c line of 7611 on this EVAL....
View ArticleAD5933 Lower Limit of Frequency
I tried to measure impedance with 1-2kHz signal with AD5933. However, the chip do not work or return different magnitude. Is there any suggestion to work this chip? According to the datasheet, it says...
View ArticleRe: adv7611 don`t start
yes. I try to start alone 7611 by myself microcontroller. in schematic of EVAL board (because it clear).i have no output from HDMI. in output i see trash signal. if i put signal to HDMI input or...
View ArticleRe: Simulink ZC702 AD9364 fmcomms4-ebz
Hi David, Normally the Windows SDK should be enough, that's what I'm using on my machine. The simplest thing is to try to install Visual Studio Express, it is free and comes with all the necessary...
View ArticleHow to configure AD9361 with a FPGA?
What's the proper order to configure AD9361 with Spatan 6 ? I think the reference datashet is not very clear.@
View ArticleCharc ADSP-21489 boot problem
Introduction: processors BlackFin (ADSP-BF533SBSTZ400 firm Analog Devices) and Sharc (ADSP-21489BSWZ-4B firm Analog Devices) are loaded by SPI with FPGA (XC6SLX150T-3FG676I firm Xilinx). FPGA provides...
View Article