Re: Frequency Modulation with AD9910
After every loading operation listed I am issuing an io_update.
View ArticleRe: Question for AD8361
Hi bkamak, Thank you for your good answer.OK, we will study with eval board or sample doing for offset changing. As for your ADL5501,Our frequency is 3MHz so ADL5501 is not fit for our product, I...
View ArticleThe reinforced isolation of CAT-2 300V EN61010-1 3rd for ADuM1301/1401BRWZ
Dear Sir/Madam, maybe Dave C. Question:Do you have the evidence document of the reinforced isolation of CAT-2 300V EN61010-1 3rd?Otherwise can you recommend another i-coupler fit for the reinforced...
View ArticleRe: Settings of apply external audio to HDMI TX of ADV7623
Hi Paul, Sorry to reply you late. I will double confirm it. Regards,Jacy
View ArticleRe: Transmitter with DPD system working at 1-30 MHz transmit frequency
Dear Robin,I am looking for hardware support. I need a transmitter and receiver (as feedback) system working at 1- 30 MHz range and I need access to baseband data to implement my own algorithm.I am...
View ArticleRe: AD2S1200 SIN/COS inputs are between input Vpp and threshold LOS/DOS.
Hi Sofy, When the signals go below the specified input voltage range, you could expect a degradation in the accuracy of the output, although, this is very minimal. With this,It is recommended to keep...
View ArticleRe: Refection in REFA of AD9525
Paul： In my design, HMC910 is the source, and AD9525 is at the destination of HMC910. I am thirst for new advice. Thanks Regards Jacky2014-04-23
View ArticleRe: ADIS16485 - data ready indicator does not fit output rate
Hmmm, it sounds like you are pretty close. Here are a few comments:The RAM locations contain the "working memory," so the settings take effect, regardless of the flash memory contentsAre you allowing...
View Articlecan4linux and serial RS232 incompatibility
Hello, I got a problem when I try to use both a can communication (Can4linux driver) and a serial RS232 on port com ttyS0 : - If I use each one independantly in a compiled program, everything works...
View ArticleRe: ADuCM360 ADC
What is your input voltage?Have you biased up above 100mV - see input specifications!Also have a look into the following threadhttp://ez.analog.com/message/115302#115302
View ArticleRe: Help!!! My AD7192 is working way to well, without an input buffer...
Shannon, The spec table guarantees that in unbuffered mode, the input current is higher, but you can get within50 mV of the rail. In buffered mode, the input current is lower, but you can only get...
View ArticleADuC7061 Source code for CN0196
Hello! I have the evaluation boards for the circuit from the lab #196 (http://www.analog.com/en/circuits-from-the-lab/CN0196/vc.html) and i was hoping to make some modifications to the source code...
View ArticleRe: Choosing the right ADC for the job
The zero Ohm resistor can be eliminated and a simple trace be used in the final application. Zero Ohm resistors may be used for a number of reasons. In the case of evaluation boards, they are often...
View ArticleRe: AD9361 BBPLL fails to lock on prototype
Yes, SPI works, hence the logs I posted of the SPI transactions. 1Vppk is the amplitude of my reference signal. I stopped the program during calibration and dumped all the registers. The only...
View ArticleWhat is a difference between AD8418 and AD8418A?
HiI checked the AD8418 and A datasheet.Those are almost same, but those actual features seems a little different.What feature has improved? Regardsmoto
View ArticleRe: AD7731 Communication Issues
Hi. Can you please do the following? Upon power-up, perform a reset(either hardware through /RESET pin, or a write operation of at least 32 serial clock cycles with DIN held high). This ensures that...
View ArticleRe: ADV8003 TTL Output connect to 18Bits TFT pannel
The 8003 does not have a color space converter between the VSP and TTL pixel port output. Therefore the only way for the 8003 to drive a RGB LCD is possibly by-passing the VSP completely. Of course...
View Article