Re: Rx AD9361 I&Q vectors save on the ZC706
Hi Robin, Thank you for the fast reply. We need to capture a block of data (10ms worthof data @30.72MSPS), save the data to a file then transfer it to:Matlab using serial or Ethernet for DEBUGTransfer...
View ArticleRe: ADV7181D support input YPrPb(525p), output SDR 8bit 4:2:2 YCrCb ?
The basic script you have above is good with a few changes 1) Only the writes to address 42 are ADV7181D related. you can ignore the writes to address 56 2) Set 0xC9[3] = 1. You might need to tweak...
View ArticleRe: AD9467 Display output on console
Hi Rohit, Where do you want to implement the filter? On software or hardware (hdl)? You can find a lot of examples on the internet, for FIR C implementation. If you want the hardware way, it going to...
View ArticleRe: Recommendation or suggestion for video decoder in new design ?
Set OP_FORMAL_SEL[7:0] = 0x00 see hardware guide UG-214, Table 101
View ArticleRe: Disabling TX on AD9361?
An attempt to document things is started here:http://wiki.analog.com/resources/tools-software/linux-drivers/iio-transceiver/ad9361-customization Also you can use the GUI and look at the attribute using...
View ArticleRe: 1701 division block
Hi Bob Its not been a good day! I started off using the peak compressor module in my project but it has a mute function that cuts the amplification for very low input signals that is not mentioned in...
View ArticleHow to compute the Energy values ? (ADE7880)
Hello,I am working with an ADE7880 and I successfully get the Current, Voltage, PowerFactor, ApparentPower and ActivePower.I am able to compute the real values of the Current, Voltage, PowerFactor,...
View ArticleRe: ADM1270 Design Question
Jacky, It sounds like your application may not be a good fit for the ADM1270. Since the ADM1270 is designed to work with PFETs and not NFETs. This limits the number of FETs that are suitable. If the...
View ArticleRe: Low Cost Accelerometer Needed to Measure Concussion Impact
Hey Mark,Thanks for the info. Is there anothe LOWER cost can use because the ADIS16448 gyroscope costs about $750 each while the ADXL377 accelerometer costs about $4.50.thanks again for your help.Mario
View ArticleRe: AD9910 - Simultaneous use of RAM and DRG- Is it applicable?
Hi Freddy, Louijie is correct. The AD9910 DRG and RAM use the same registers inside the part so only one can be functioning at a given time. However, the AD9910 has a second ramp generator exclusive...
View ArticleRe: AD9910 - Simultaneous use of RAM and DRG- Is it applicable?
Hi Freddy, Some ADI colleagues pointed out that I made a mistake. I was thinking of the Single Tone Profiles instead of the DRG, and those cannot be used in conjunction with the RAM because they use...
View ArticleClik here to view.
Re: EVAL-ADIS C/C++ Driver or Source Code Libraries
Hello Pierre-Yves,I have attached a new DLL to this message, which makes the functions "COM visible," for C++ development environments. Our software engineer was able to do some very limited testing...
View ArticleRe: Multiple AD9361 configured using Kintex-7 FPGA
1. If you have three AD9361- you need three cores unless you have external synchronization and merge the functions within. This affects the DMA interface (you will now need to pass the 12 channels to...
View ArticleADF4106 lock_detect still active when Ref in removed
We are seeing a problem with the ADF4106 analog lock detect. It is still showiing the part is in lock (not all the time but ocassionally) even when the Ref frequency is removed. Is there a way around...
View ArticleRe: ADV8003 Eval BOM
Hi Dan, Which evaluation board are you looking at? EVAL-ADV8003-SMZ or EVAL-ADV8003-SMZ-P? Regards,Matt
View ArticleRe: CEC clock of ADV8003
Sorry for the delay. I was out of the office for a while. I will check again on this question. -Matt
View ArticleRe: Sigma300 (ADAU145x) Q&A
Hi, The broken DC connector on the EVAL-ADAU1452MINIZ is troubling. The connector on the board is a Switchcraft RAPC722, we have used these for many years and have not had any complaints. I apologize...
View ArticleIssue running vivado reference design
I am having issues running the vivado reference design. I have everything building correctly except that a few of the block design pins are not connected. This was the design in the hdl git directory...
View ArticleRe: ADP2114/2116 output current
Hi Ymsk, 1) Theoretical, it is possible to connect the two converters in parallel to double the maximum load current. However, some modifications are needed to maintain load sharing and stability...
View Article