Clik here to view.
Re: Adxl345 linux driver freezes, [raspberry pi i2c]
It's working ! thank you very much Yesterday I checked it for quick and i forgot to change rate to 3200hz, now i wanted to use it and i got freeze again
View ArticleRe: ADV7183B Question
Can't really get it triggered on the rising edge, beside if you did then the entire image would shift to the left. Their overlay box has poor sync edges. Something changed from now and 10 years ago....
View ArticleAD9361 VDD_ITFC_on while VDDx_off
It appears the AD9361 isn't picky about the power-up sequence, but I'm considering leaving the VDD_INTERFACE powered while the +1.3V rails remain OFF until selectively enabled sometime later. Will this...
View ArticleReceiver for Analog Front end reduced range lvds output
ADDI7013 has a reduced range lvds output ( 200mv). My FPGA mini lvds input range is 200-600mv as receiver.Is it safe to use mini lvds as the receiver? ADI7013 's pixel rate is 75Mhz. Does it work...
View ArticleRe: ADV7513:Register setting file
What Are you measuring the jitter on one of our reference boards? Jitter is has several possible sources. a) PVDD power and PLL filter has to be very cleanb) noise injected by other circuits 1) The...
View ArticleWhat extra setting needed to get VIDEO TALK THROUGH example working?
Dear All, I have started my work on ADSP-BF-561 KIT recently. After getting through UART and general projects, I am trying to do Video - Talk- Through Example. I have connected a...
View ArticleRe: ADV8003 Eval BOM
Here is the BOM for the EVAL-ADV8003-SMZ which has all of the same components as EVAL-ADV8003-SMZ-P, plus the ADV7625 and associated components. Let me know if you have any questions. -Matt
View ArticleRe: Plug TXA or TXB would affect the other output port normal display when...
Hi Jane, when we doing hot plug , to disable hdcp and sending the edid to RX that to intimate the status of TX has changed , the above part is used. Since you are using splitter mode , TXA is used as...
View ArticleRe: ADIS 16405 Output Problems Using Raspberry Pi
I have checked the wiring and nothing was connected to the DNC lines so it would appear that this was not the issue.
View ArticleRe: ADuC7060/61: What to do with unused JTAG pins?
The pull-ups required if you need to connect to your board with the JTAG-Emulator.If not, than you can connect to a fixed level.nTRST on the ADuC706x has a GPIO functionality I tested as input only.TDO...
View ArticlePossible reason for H.264 Encoding error
Hi, I am following the example from the software module to create an H.264 BP Encoding Application on Blackfin 561. In my recent performance test, I encounter some issue with the encoding at low...
View ArticleClik here to view.
Re: EVAL-ADE7753 Software error
Hey Hamni First ,sorry for delaying , But i have mid term exams Today I get some screen shots from my pc. Hamni notice that , there are error in reading , and the RMS values not accurate , etc... I'm...
View ArticleClik here to view.
ADXL345 Data read rate
Hello, I'm having some issues with the data read rate on my ADXL345. I'm using I2C to connect the ADXL345 to a Raspberry Pi using the Python library here:...
View ArticleRe: Circuit Board Desgin of the ADIS16488
Hi RobinUofC, Yes, you can cut that part of the ADIS16IMU1/PCB off. If you have one, you should be able to see where all of the traces are, as this is only a two-sided PCB. I am not 100% sure of what...
View ArticleRe: gpio-addr-flash memory window overrun with large I/O block size
Have you configured the CPLB properly for your gpio expanded address space? Check this thread for some discussion on this topic http://ez.analog.com/message/133787
View ArticleRe: Plug TXA or TXB would affect the other output port normal display when...
Hi, Sir,Is it possible to meet this need that TXA or TXB can display normally, which won't be affected by hot plugging the other TX end. If it is possible, how cant it be achieved? Can you kindly tell...
View ArticleRe: bf516 network sometimes become very slow
This sounds strange, what's is your network application in your product, do you see a real "slowing down" for your actual network application?
View ArticleRe: ADIS 16405 Output Problems Using Raspberry Pi
OK, that is good. I fear that the device was already limping when the +/-3g observations were made, but that is really hard to say for sure, so we look forward to hearing how this works when you have...
View Article
