Re: How to enable ETH1 in uClinux
As far as I know the MAC driver for eth1 is not ready nor verified yet, so your code changes in board file is not enough to bring it up.
View ArticleRe: No HDMI output in latest Ubuntu design for ZedBoard
Same problem. - I checkout latest HDL libraries and project scripts from https://github.com/analogdevicesinc/hdl- Built HDL libraries and ADV7511 for ZedBoard using Vivado 2014.1 - I just needed to...
View Articleseveral questions about STDI
adv7482 or adv7441a How to calculate BL?where can I find the detail parameter about different video format(RGB and HDMI) SVGA@60hz(800*600@60hz),according to 《VESA and Industry Standards and...
View ArticleRe: CN0274 Evaluation Board
Hello - Thanks for the quick response. I've been doing a bit more research and I really like the solution provided in this thread:http://ez.analog.com/message/40001 Using the PIC10F322 is really...
View ArticleRe: AD8352 DIFFERENTIAL AMPLIFIER
Thank you for ur valuable information....... Am applying the input clock with upto 50MHz, What would i do to make this circuit working for my input requirement.....
View ArticleRe: AD8352 DIFFERENTIAL AMPLIFIER
thank u umesh....... what would i do to make this circuit working for clock input with upto 50MHz, without introducing DC offset at the o/p.........
View ArticleRe: AD9254 EVAL
Dear Tony, Thanks for your response.We have already shipped these boards to customer.The issue currently is that the software is not showing up AD9254 as an option to select. Customer has tried to read...
View ArticleRe: Question: SPORT, TDM and DMA
Hi Yli, No need to use two ISR's. Because the FS and the clock are locked (and probably routed to the same pins as in my situation) the data is received in both sports, even if just one is signaling...
View ArticleRe: ADV7480 HDMI/MHL receiver
All the registers defined in the global structures"kaAdv748xRecHDMIPllInitTable","kaAdv748xRecHDMIEqInitTable","kaAdv748xRecHDMIMiscInitTable","kaAdv748xRecMHLEqInitTable"...
View ArticleRe: AD9361 Linux Data Verification
The scope uses single shot DMA mode. A single DMA transfer is limited to 2^24 bytes due to some addressing limitation. However the Linux driver supports continues DMA transfers using the MMAP...
View ArticleClik here to view.
ADL5387 and ADL5385 spurious issue
Hello , We find there are some spurious(like as little oscillation) from ADL5387 and ADL5385 chip when we make system evaluation.There are also similar spurious signal on this two evaluation...
View ArticleRe: AD9361_Initialization
Thanks Dragos. Which boardyou are usingforthe reference design?
View ArticleRe: AD5933 + AD8606 Nonlinearity problem
Hi, what do you mean by non-linearity issues? Could you show an example Say that, measure a capacitor or inductor directly could generate stability issues in the opamp due to the imaginary...
View ArticleRe: Vivado ZED project no I2C connection to ADV7511
Hi, The error you are getting suggests that the I2C pins that the adv7511 is connected to are not correctly connected in the Vivado project. Make sure that the Vivado upgrade did not mess up the...
View ArticleRe: Highlighting of bool keyword in CrossCore Embedded Studio
hiamclno no! firstly,sorry for my amphibolous expression, I means why the color of function 'adi_pwr_Init' isn't like the color which the 'bool' look like.In other words, I wish the color of the lib...
View ArticleRe: Poor SNR of ADV7180 and ADV7391?
Hi, 46dB does sound low for RAMP SNR, I would have expected your result to be in the mid fifties. What are you using as a video source and video measurement equipment? Could you try the following:...
View ArticleClik here to view.
Re: AD5933 + AD8606 Nonlinearity problem
This is the circuitAs Zunknown inductive load of 50 mH is placed. Also I am using ADG706 for calibration and feedback resistor network.In previous post you can find attached picture which presents non...
View ArticleRe: Possible reason for H.264 Encoding error
Hi Eric,Please provide a few more detailsAre you using the ADSP-BF561 EZ-KIT Lite board? If yes, which revision are you using?Which version of H264 encoder module are you using ?What are the values of...
View ArticleRe: FMCOMMS2 and Vivado 2013.4
There seems to be the same Problem with Vivado 2014.1 is that right?
View Article