Can ADA4000-4 work on +-18V power supply?
Hello, I am searching one kind of opamp to work on +-18V. ADA4000-4 may be the choice as the datasheet said that "±4 V to ±18 V operation". However, I also found in the datasheet that the maximum...
View Articleinterfacing AD9144-ADRF6720-EBZ to FPGA
HiIs there a way I could interface the AD9144-ADRF6720-EBZ (evaluation board of TxDAC integrated with two IQ modulators and LO) to a Xillinx FPGA with FMC connector?The board has a DPG3 compatible...
View ArticleHow reliable are the multiplexers ADG706 and ADG726 in space?
If these ICs have been used in satellites (LEO), any experience shared regarding its reliability is appreciated. How immune are they to Single Event upsets caused due to impingement of high energy...
View ArticleClik here to view.
Re: AD8367 - Maximum Output P1dB Point in 50Ohm configuration
Hi Sir, Thank you very much for your valuable support. We have simulated your S-parameter files and the result is attached for your reference. The output return loss result over the frequency is...
View ArticleRe: Interfacing AD7764
Hi MClifford, Thanks for your reply. >> FSI signal - Clock this relative to the SCLK that you receive from the ADC "SCO".Do I need to tap the SCO to MCU Interrupt also to sync FSI signal wrt SCO...
View ArticleRe: ADE7816: Peak detection
I've never fully understood how the IPEAK stuff works on a 7816. As an experiment, with 50Hz ideal inputs on V and I, I've left the CHANNEL_SEL bit at its default of 0 so I'm monitoring channels A, B...
View ArticleRe: TCPIP1940 protocol specification
After more investigation with a TCP server in debug mode, I have found that the packets are far less cryptic than I thought first (the problem with Wireshark is to find *all* packets containing data......
View ArticleClik here to view.
Re: Can ADL5391 ENBL pin drived by MCU ?
Thanks.I have a question.When ADL5391 work, it was very very heat,that is the chip temperature is very high. It is normal?What can I do with that can improve it?
View ArticleADG3304 - I2C
Is it possible to use the ADG3304 for I2C level translating (3,3V Master, 5V slave)?
View ArticleRe: axi_ad9361 supporting documentation
Leonard: Have a look at: https://ez.analog.com/mobile/mobile-access.jspa#jive-content?content=%2Fapi%2Fcore%2Fv3%2Fcontents%2F117413 That points to...
View ArticleI am not able to find the Camera EI3 Extender Board Support Package 1.0.1....
I have installed the CCES 1.1.0 evaluation license version for ADSP BF609 EZ-KIT-1.0. I required the "Camera E13 extended board support package(BSP)" to use those the Sensor (MT9M114) driver with EZ...
View ArticleClik here to view.
Re: interfacing AD9144-ADRF6720-EBZ to FPGA
Thanks Neo for mentioning the required Xillinx licenseI am still looking at layouts/schematic/pictures and the Z-Pack hm-zd connector on the this EBZ evaluation board seems to mate with the JESD204x...
View ArticleClik here to view.
AD-FMCCOMMS1 always cuts sampling frequency in half?
Hello,I am trying to transmit a wideband IQ signal with AD-FMCCOMMS1+Zedboard.Using the reference image on AD-FMCOMMS1-EBZ User Guide [Analog Devices Wiki], and iio-oscilloscope,the DAC sampling rate...
View ArticleRe: LET threshold for AD8561S?
HARRY,CHDJ75 ASKED ABOUT SINGLE EVENT EFFECTS LATCHUP RADIATION HARDNESS. I HAVE THE SAME QUESTION. DID ADI OR A 3RD PARTY PERFORM SEL/SET TESTS ON THE AD8561S AND HOW MANY MEV*CM**2/MG IS IT RATED FOR?
View ArticleRe: ADP5054 ADISimPower Tool
Dear Kevin:I already to download the ADP5054 ADISimPower at ADI Website. Another I would like to refer to ADP5054 EVB Board PCB Layout, can you provide Gerber file to me a reference? Thanks~ My...
View ArticleRe: Dynamic bass boost in a 2.1 stereo design
Hi Bob, Thanks for the information! I wonder if there is any graphical description of the gain that is applied by the dynamic bass bost (gain vs frequency)? For example: Settings:Boos Freq = 45HzBoost...
View ArticleRe: RMS+PEAK Combo - noise problems ...
Hi Brett, I could not find out how to start a new discussion but I send the question directly to you :-)! I wonder if there is any description or"curve" of the gain that is applied by the dynamic bass...
View ArticleClik here to view.
HMC980LP4E Powering 4 TGA2598-SM
Hi I am using the HMC980LP4E to power 4 TGA2598-SM on a single board.The design is attached and it would very appreciate your review and recommendations. Thanks a lot.
View ArticleRe: HMC980LP4E Powering 4 TGA2598-SM
Hi morraviv, One of the main purpose of using HMC980 to bias and AMP is to continuously monitor Idd of the DUT and change Vgg accordingly. This will provide significant improvement to part to part and...
View ArticleRe: FFT in BF506
Hi Francesco, I am attaching a simple code which explains how ACM can be configured to achieve ADC sampling rate of 1.5MSPS. (I have set SCLK as 100MHz, therefore I could achieve 1.5MSPS through...
View Article