Re: Signal input ranges on ADAS3023
Hi, Let me check on this. I'll get back to you soon. Regards,Karen
View ArticleADL6010- Power Detector Frequency Response?
Hi All, I have a question regarding ADL6010 - Fast Responding 45dB range, 500MHz to 40GHz Power Detector. I measured frequency sweep (29-31GHz) vs. Vout (at Pin = 3.5 dBm and Pin = 20 dBm) on the EVAL...
View ArticleRe: AD8605 EMI immunity
Hi, Shumpei. There are many ways to filter out EMI. You may want to implement the circuits on pages 5 and 6 (to eliminate EMI at the inputs) and pages 8 and 9 (for the outputs) of this article -...
View ArticleRe: AD9361 NOOS and AXIADC
Hi Wade, The AD9361 core is an IP that needs to be included in the FPGA. This IP transfers data to/from the FPGA from/to the chip in LVDS mode. For Altera, we have a design based on c5soc...
View ArticleRe: ADXL345, 3200Hz Data Ready makes ideal time interval?
Venkat: Why they did not write down the variance data rate in datasheet I wonder the variance occurred from clock source or latency while I do something in ISR(data ready).If originally it is from...
View ArticleRe: Input voltage of absolute maximum ratings for ADCMP580, ADCMP581 and...
Hi, Akihiko. According to your question: The condition I showed in my question were “VCC = 3V, VEE = -3V and Input voltage = 3.9V”.I feel like ADCMP580 can work well in this condition if the ABR is...
View ArticleRe: ADAU1761 Distorted Output
Hi Lisa, Thanks for reminding me I wasn't able to notice my post. Dave, Thanks for the inputs! I have tried to increase the input level up to 250mVrs to no avail. This is the evaluation board for...
View ArticleClik here to view.
Re: CM40x does not enter deep sleep mode
Hello Prveen H, Could you share it with me if you have CM40x power consumption data in deep mode? Best Regards,Mack
View ArticleRe: AD5933EBZ-Problem regarding phase
I done with 20khz frequency.the results are attached.the phase value is decreasing according to the increasing frequency.
View ArticleRe: failed to boot kernel on zedboard with adv7511
U-Boot 2014.07 (Dec 10 2014 - 18:03:02) Board: Xilinx ZynqI2C: readyDRAM: ECC disabled 512 MiBMMC: zynq_sdhci: 0SF: Detected S25FL256S_64K with page size 256 Bytes, erase size 64 KiB, total 32...
View ArticleRe: About AD9548 DPLL register setting
@Hi Paul, Thanks for your reply. I have try you suggested on EVB , it's works on DPLL free run once setting 255.76 MHz.Then divide 16 on Q0 ,Fout =14.11 MHz.But, how can I used it on profiles 0 which...
View ArticleRe: Problem with AD8293G160
Hello, I measure both input and output with two different input voltages and perform the calculation You suggested before but the Gain is lower than 160. (from 120 to 140). I removed C25, C26, C27 and...
View ArticleClik here to view.
Re: cn0217 wrong configuration
Hi Azita, I tried to measure 1uF capacitor using the said configuration and it seems that the measured impedance and phase is not the same with the given results in the application note. You have a...
View ArticleClik here to view.
Re: Does your ADC made from a magnetic body?
Hi Umesh, Thanks for you great support again.I confirmed that you were instructed Link AD9253EP's.It was included 4.8x10-4[g] Tin=Sn material in there.Is this correct? 2)I would like to recommend your...
View ArticleRe: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad
Here you can find some performance specs for the RF card: AD-FMCOMMS2-EBZ / AD-FMCOMMS4-EBZ / AD-FMCOMMS5-EBZ Specifications [Analog Devices Wiki] Xilinx blockset might not quite the best option, I'd...
View ArticleAD8339 eval soft for win 7
Hi The software of AD8339-EVALZ is for Win XP.Could you tell us how to use on win 7 64bit? and How to get the exe and MSI files as described in DS RevA 29/36? "Using the SPI Port" Regardsmoto
View ArticleRe: AD-FMCOMMS-3EBZ VC707 ADI example Embedded linux newtwork issues
Hi, When did you download your pre-build image?Latest Build is from: 2015_03_19Linux SHA:120acb20f29451f747d692300e4ba79ea49239a4 Linux branch:2014_R2 Linux...
View ArticleClik here to view.
Re: How to install AD9361 driver on yocto (bitbake)
Hi, thx for your prompt response, and sorry for my late,I was working on another project.If you are familiar with bitbake, can you give a few more details...,I create a layer "meta-fmc" where I specify...
View ArticleRe: Using 2 FMCOMMS1 boards in ZC706
I am guessing you meant by "additional drivers" also includes the HDL modules replicated. The modifications you need to do on software depends on how you are using the i2c interfaces -- if it is a...
View Articleto Send a Data from ADV7511 to Oculus Rift DK2
Hi, I am working on a Hardware project that uses a Oculus Rift DK2. My System consists of ADV7611(HDMI Receiver), ADV7511(HDMI Transmitter), FPGA and the Oculus Rift DK2. PC(HDMI Out) --> ADV7611...
View Article