Re: AD7794 issue: Measuring voltages from batteries and Shunt resistors
Hi, We're looking into this. We'll get back to you as soon as possible. Thanks and Best Regards,Chris
View ArticleRe: ADV8003/8005 OSD menu , start position&end position
Hi, Do you have our evaluation board ADV8003 or ADV8005? Are you using Blimp tool to design OSD? Did you go through the below page? Blimp OSD Designer tool for NatureVue™ ADV800x and Advantiv® ADV7625...
View ArticleRe: ADV7850 Output HDCP hangs
Thank you GuenterL, we made the development w/o any EVB. In between the solution is found.Tx Main (bank $B8) reg $97[6] BKSV_FLAG goes high and has to be cleared by writing a '1' into it.Otherwise the...
View ArticleRe: How to get the captured spectra data stream from iio oscillascope...
Hi Jie, My advice to you is to check out the iiostream.c example and learn how to capture ADC samples for long periods of time. Then you can save all those samples to a file. There are lots of FFT...
View ArticleClik here to view.
Re: FMCOMMS2 Vivado 2013.4 build works, but not quite right.
Hi Santhosh, I want to thank you for your valuable feedback. At the first point a don't really see the connections between the DDS frequency and saturated samples, but I will do some further...
View ArticleRe: AD1940
Hello,I'm the customer who got the problem. The SigmaStudio 's version that I used is Version 3.11.Build 2, Rev 1396.The block is "Level Detector Designer". You could get it form Tree...
View ArticleRe: AD9856 Evaluation Software
Hi,I have attached 2 eval software installers.Please let me know if one of them works or not. -Sittie
View ArticleAD7793
Hellow.I'm mesure 100 mV from Pt100. I set gane from 1 to 128 and using internal Vref.I recived such 16 bit digital codes from ADC:x1 - 5413x2 - 10819x4 - 11038x8 - 21722x16 - 25780x32 - 26957x64 -...
View ArticleCapacitance Cds(on)
Hello, we are using two Multiplexer/Switches ADG1404,ADG1436 to change measurement ranges in an application. While measuring low currents we use a high resistance of about 1MOhm to convert the current...
View ArticleRe: Synchronization issue of multiple ADE7913
Thank you David a lot for the explanation.
View ArticleRe: Capacitance Cds(on)
Hi Ronny, It sounds like you really need a low capacitance switch. If you are using 1MOhm do you really need to use low Ron switches like the ADG14xx family? If not I would suggest you look at the...
View ArticleRe: ADE7878 Overcurrent interrupt question
Hi dlath, Thanks for your reply. The peak detect function is more clear now. I have been trying the 'All Registers Access', but I can not seem to trigger an IRQ1 interrupt. PHSTATUS indicates the right...
View ArticleRe: the Advanced Expert DAI can't work for Vsdsp++5.1.2
Hi, I have moved this from the Processors and DSP community to the SHARC Processors community, and will continue the discussion here. When you ran "regsvr32.exe ...", did you ensure you launched the...
View ArticleClik here to view.
Re: ibis simulation
I don't recognise that part number, but a Popular Search Engine's results suggest it is a Texas Instruments part - I recommend contacting their support channels for IBIS Models for this part....
View ArticleRe: ad-fmcomms1-ebz programming FPGA
You probably get this error, because you did not programmed the board, with the software. You always need to make sure, that the system is up and running, before you trying to connect to the debug...
View ArticleRe: AD9361 charge pump calibration.
Hi,Thank you for replay. The maximum size of one BRAM block on Spartan-6 chip is 64K. I have a three blocks in my design and I modified the linker script: Section name Memory region.text...
View ArticleRe: How to communicate with ADE7754 to make an energy meter with PIC18F2520
hello sir,,,,, after long time..i need your help again........i have made the single phase energy meter with vrms, irms and line freq display........ some pieces was sold ........now customer feedback...
View ArticleRe: Timing contraints not met for FMCOMMS2 project build on ZedBoard
Hi Adrian, I've now tried building the project on a different WinXP machine that only has Vivado 2013.4 installed. I still get a timing constraint error and the build doesn't seem to like having only...
View Article