Re: ADV7181C Analog RGB
Dear dave, Thanks for your reply there is any setting i can do to decode 768 x 576 pixel 625i RGB on ADV7181 chip.Please Suggest us regrading 768 x 576 pixel 625i RGB decode.there any other devices...
View ArticleRe: ADV7181c
Dear GuenterL, Thanks for your reply My Analog RGB input is 768 x 576 625i. i couldn't how to set to this pixel input decodeCan you help me with this Thanking youRegards,Balaji
View ArticleRe: Flash programming in ADSP21489
Dear Sir, In our design, we are using both ADSP21489 and Spartan FPGA to cater our application requirements. we proved the functionality of our design when both programs loaded through JTAGs. Now, I'm...
View ArticleADIS16209
I use ADIS16209 evaluation board with TI controller. I not set means not write any control register & assume that it is ok as per datasheet.1. My target is to measure X or Y axis both side with...
View ArticlePin Muxing in CCES 1.1.0 for ADSP-BF538F
Hi All, I am using the black fin processor ADSP-BF538F in one of our project. I am using the cross core embedded studio 1.1.0 IDE for my development. I followed the procedure to create a cross core...
View ArticleADRF6518 output noise, dBV/Hz or dBV/sqrt(Hz)
hi; I saw the output noise density of ADRF6158 is -104.6dBV/Hz, but the unit in datasheet of ADRF6516 is dBV/sqrt(Hz), what is the different between? or just a print error in datasheet of ADRF6518, it...
View ArticleBF609: second wake-up issue with hibernate mode
We are working with the BF609 rev0.2, 2013 blackfin-bvuildroot.1-We are able to enable hibernate mode (echo mem > /sys/power/state)2-Wake-up done from CAN-RX3-We are able to able to run the second...
View ArticleRe: Question about the ADV7180 with the output picture shake
Dear GuenterL The video source is the Camera. and there is no anti-aliasing filtering in front of the ADV7180 inputs. which signal should I to test when debuging the circuit?
View ArticleRe: ADV7181C Analog RGB
Hi Balaji, You'll find scripts of settings for many configurations including, I believe, that one on the design support files page for ADV7181C: ADV7181C Design Support Files Dave
View ArticleClik here to view.
Re: AD9361 Linux Data Verification
Hi Di, At long last, I got past the error listed above. It turns out that the super classes you guys are using for the Simulink blocks only work with 2013b or greater (which I had my license updaded to...
View ArticleClik here to view.
Re: ADIS16480, SYS_E_FLAG[4], Source of over-range?
QUESTION ANSWERI don't see an over-range in this data. Would it be possible to provide data for all of the inertial sensors (gyroscope, accelerometer, magnetometer), during the SYS_E_FLAG[4] = 1...
View ArticleADIS16480, register questions
Hi Mark, I'm sorry I didn't put my questions together. While I am testing(only EKF_CNFG is changed, = 0x0203), I am having new questions, 5. Regarding data captured below(totally 5 registers are...
View ArticleRe: ADIS16480, register questions
QUESTION6. In eval-adis, there is a NULL_CNFG in page 3 with address 0E and default value 070A, what is this? ANSWERThe NULL_CFG function is valid for the ADIS16485 and ADIS16488, which share a common...
View ArticleClik here to view.
Re: ADIS16480, register questions
QUESTION ANSWERIf I understand correctly, EKF_CFG[1], this only disables the influence on the angle output estimation process, through the EKF. It does not disable the magnetometer measurements or the...
View ArticleRe: ADIS16480, register questions
QUESTION8. what does this imply, big difference(2.4 degree/sec) of gyro output between two consecutive samples under 2460Hz? Can we deduce the acceleration? ANSWERI might need more information on this...
View ArticleAD7176: how to read channels in order
Hi, I'm trying to access an AD7176 from an AVR32 microcontroller via SPI. I can read and write registers fine, but my problem is, when I read the converted data, the channels seem to appear in random...
View ArticleStreaming ADC data through ethernet
Hi, I have recently started working on KC705 + fmcomms3-ebz (Vivado 2014.2). I am building the reference design hoping to get it working. I have experience in HDL coding however I am a newbie in...
View ArticleClik here to view.
Re: Something wrong with level detector in 1452
Hi, Perhaps you would find it easier to use an arrangement like that shown below, which takes advantage of the 145x's log2 function to calculate dB (relative to full-scale) from an envelope...
View ArticleAD9361
Hi,I want to use the AD9361 and a FPGA for a certain application together with the demo suggested by ADI.In order to select the proper FPGA I would like to know if anyone can tell what is the...
View ArticleClik here to view.
AD9822 noise
HiI am designing an ADC circuit for CCD, I am used ADC9822 and the circuit is exactly same as datasheet.The sampling rate is 1.25MHz and ADC is programmed in single channel and CDS mode. The noise at...
View Article