Re: ADuC7126 Pin P4.5 behavior when JTAG is connected
Alex,More findings to the "strange" behavior:1)When emulator is in control via JTAG, P0.1 and P0.2 show the same pulses when processor runs (identical digital information), both pins show THE SAME...
View ArticleRe: EA bit behavior in burst mode reads
Thank you for your work with the ADIS16364 and for posting this question. You will need to read the DIAG_STAT register to clear all of its flags, except the power supply flags. I hope that helps.
View ArticleStepsize for ADV 202
Hi,I have a question about setting the parameter of 'stepsizes', when using ADV202 for JEGP2K compression.The original image is 320X256, 14bit, the rate-control algorithm is set to 'Target Size per...
View ArticleRe: ADIS16251 vs. ADIS16265 Performance
There are a number of things that could be influencing your results. I am not sure how many parts you have included in this study, but over a population of parts, we have found that the best results...
View ArticleRe: Re: Re: EVAL-ADIS - writing your own logging software?
Just wanted to check back in. Has this helped? Our administrators would appreciate a Correct Answer designation if this has addressed your questions. If not, we look forward to any follow-up...
View ArticleRe: ADP1047/1048
Hi NC, See the answers bloew.1. There are two OT fault flags in the Flag setting in GUI. What differennce between them?one is OT_warning and the other is OT_fault. the OT_warning is for warning only...
View ArticleRe: ADP1051 Evaluation Board Transformer & Inductor SPEC.
Hi Jacky, which part are you using? what is the power do you want to design? would you mind to have a chat through the phone call? 750341378 Wurth Electronics Midcom | 1297-1029-ND | DigiKey7443630420...
View ArticleRe: ADXL362 power consumption in wake-up mode with FIFO data storing
Hi Neil, Thank you very much for your reply. Best regards, Nikkee
View ArticleClik here to view.
Re: Is ADV7511W compatible with the input signal of progressive BT.656?
Thank you for your help!
View ArticleBF60x PPI examples with interrupts?
Hi, I was wondering if there are any code examples outlining how to configure the BF60x so that incoming PPI data is automatically streamed to a DMA channel and to trigger an interrupt? Thanks!
View ArticleEVAL Source code for UG-209 ADXL312 board
We just received the ADXL312 evaluation setup (UG-209 document) and would like to directly access the main board from a PC to do some custom programming. Is it possible to get the LabVIEW source for...
View ArticleSHARC SPORT skipping samples in TDM16
We are using a SHARC 21489 to interface to a DAC in TDM16 mode with 16-bit audio at 16KHz. My math is: I want 16KHz audio and PCLK is 200MHz. I need 16 channels, so 200M / ( 16 chan * 4 * 16K * 16 bits...
View ArticleRe: How to start up ADV7513?
GuenterL, Thank you for your help, we not just evaluate the ADV7513 we had the prototype built for other experiment too.I did exactly as you advised, unfortunately there is no sign of video on the...
View ArticleRe: Re: BF516: gnICE JTAG 3.10 Kernel debug symbol mismatch using gdb/gdbproxy
I had incorrectly been running two separate builds; one with buildroot set to uImage then one set to vmlinux. I have changed my process to build uImage which creates a vmlinux file as an intermediate...
View ArticleLooking for a bigger package version of ADG3123
I have a project where I am trying to take a 3.3V GPIO pin out of an SoC (Raspberry Pi to be exact) and use it to drive a control input that wants to be >= 15V. I found teh ADG3123 which fits the...
View ArticleRe: How to start up ADV7513?
1) Make sure the HPD signal is high on the output connector. Usually the monitor sets the signal high indicating it's connected. Then run the script 2) Make sure the TMDS lines are about 3V, this...
View ArticleRe: Help with rebuilding
FWIW, today I grabbed the latest version of the HDL repo and updated my working files to the tag "fmcomms1_v2013_4_2014_07_25". Using Vivado 2013.4 gave me errors relating to invalid "IP Identifier"...
View ArticleRe: ADIS16251 vs. ADIS16265 Performance
Hi NevadaMark, The values that I gave were in decimal so by 260 I meant 0x0404. Sorry, I should have clarified. Thanks for the suggestion on these settings. It makes sense that undersampling would...
View ArticleClik here to view.
Re: How to start up ADV7513?
GuenterL, I have not used the scope yet, but the 65 MHz HDMI_clk provided to ADV7513 is the same clock source to generate video output, clk was generated by a PLL, goes out of the FPGA via a ODDR2...
View ArticleModulation config files for AD9958 Evaluation Board
Hi, we purchased AD9958 Eval board ,powered up and output single tone frequency all are OK with AD9958 Eval software. In Eval software ,I want to test...
View Article