ADF7242
I am using ADF7242 for tranreceiving application. I have interfaced ADF7242 daughter board to one microcontroller. I am able to make communication with ADF7242 over SPI as i tried to read default...
View ArticleRe: Re: Re: AD9361 56MHz RX bandwidth
Why is your RF bandwidth on RX set to 56MHz while on TX is set to 40MHz? At some rates you can’t enable the RX without the TX filter. Or vice versa.Check the rates printed to see if the Filter is...
View ArticleRe: ad9361 Slow-attack Programmable Thresholds and Step-Sizes
Start the OSC application as root and you will see the advanced tab. http://wiki.analog.com/resources/tools-software/linux-software/fmcomms2_advanced_plugin After you found the optimal settings you can...
View ArticleCouldn't R/W via Memory Browser
Hello,About latest CCES and BF70x EZLITE.Once access MMR register via Memory Browser, after that, all memory address(include MMR register) is not able to read/write via Memory Browser anymore.Is it...
View ArticleClik here to view.
Re: AD5700 HART communication issues
Today, I fetched some new waveforms at TXD1 and TXD2 of MCU( while not for AD5700) under (NONE/EVEN/ODD mode. as below:I still get incorrect data from HART bus when I send one byte as path...
View ArticleAD8146 - Composite Sync Signal
Hi, Can i use the AD8146 for single ended to differential conversion of composite sync signal. Regards,Siva
View ArticleRe: help for solve a unwanted tone in ad9957
Hi Yung-Nien Chiu, Those unwanted tones are the image frequencies as a consequence of having a DAC output on our DDS. It is usually located at (system_CLK/2 - Fout) + (system_CLK/2). The ways to...
View ArticleRe: AD8170 noise figure
Hi, Dennis. Sorry for the late response. I'm already working on this. I'll get back to you soon. By the way, why do you need the NF of AD8170? Is NF critical to your application? Regards,Anna
View ArticleClik here to view.
ADIS 16364 temperature Problem
Hello, i am running an ADIS16364 and i made measurements from -20°C to +80°C to compare the Data with those who are in the Datasheet. As in the Datasheet there should be a maximum deviation of about...
View ArticleRe: HDMI splitting and reading signal
'm not sure why that would matter but it could be any HDMI sourced devicemost likely a computer but it might be a dvd player or anything
View ArticleRe: HDMI splitting and reading signal
The DVI/HDMI output from most consumer electronic devices is encrypted using HDCP. In order to purchase devices/boards that can decrypt this signal, you would need to be an HDCP licensee. Furthermore,...
View ArticleRe: HDMI splitting and reading signal
Well if you could help me out with knowing who i need to get a hold of to get that licence would be great. the application we are looking to do requires that we use a input from a consumer product and...
View ArticleRe: HDMI splitting and reading signal
Hello, More directly on point-- Video is a huge amount of data. Even SD is 270 Mbps uncompressed. There is no way you could get that over I2C or SPI regardless of what you are trying to do. Our HDMI...
View ArticleRe: HDMI splitting and reading signal
a little more on the project might helpa SD signal would be just finewe are attempting to take the video signal and read it into a ARM type processor using linux to create a independent web host for...
View ArticleRe: AD9681-SYNC PIN
Hello again Kotoo-san, As we had discussed previously, tSSYNC and THSYNC as shown in the RevA datasheet are not worst case values, I am obtaining the worst case numbers and these will be put into the...
View ArticleADuC7026 XMxPAR[15] behavior
Hi All, According to datasheet(revF), setting XMxPAR[15] allows byte write capability without using BHE and BLE for two 8 bit memory sharing the same memory region.Now, I have following question about...
View ArticleRe: ADIS16480 Position tracking Problem
We tried this using our evaluation tools and were not able to duplicate the slow recovery. One thing that you might want to try is to lower the ACC_DISTB_TH to 0x0008 (perhaps experiment). You might...
View ArticleClik here to view.
BF516: gnICE JTAG 3.10 Kernel debug symbol mismatch using gdb/gdbproxy
I am trying to debug a kernel on a proprietary ADSP-BF516 board using a gnICE JTAG. I can set hardware breakpoints and gdb can assert control over the hardware. I am unable to debug the kernel,...
View ArticleRe: Re: ADV7625 OSD Text characters are not clear during emulation and...
Hi all, The attachment is the test project
View Article