Capturing the raw data using "ADAU1772"
Hi, We are using Analog devices board ADAU1772 for developing a capturing application for multi mi data.1. Is it having any internal DSP to capture the raw data on the board?2. If not, how can we...
View ArticleCapturing the raw data using ADAU1772
Hi, We are using Analog devices board ADAU1772 for developing a capturing application for multi mi data.1. Is it having any internal DSP to capture the raw data on the board?2. If not, how can we...
View ArticleRe: AD9625BBPZ-2 IC heating Up
Hi Ian, I am getting a noise floor of -95dBFS/Hz in AD9625-2.0 ADC part. In data sheet it is mentioned that -149dBFS can be achieved. I am using a sampling clock of 1.2GHz. Kindly suggest how can I...
View ArticleRe: switch setting need for BF527 ver 2.0
Hi akshay, Thank for reply quickly, we are using both CCES and VDSP++ update 5.1.2 we found VideoAnalyticsToolbox-BF-Rel1.1.0_PROD have BF527 demo it run correctly but blackfin usb was not...
View ArticleADSP BF527 ez-kit problem on IC3021(ZVR3)
Hi Team, We using BF527 ez-kit rev2.2,we changed boot mode and return back to default mode(Mode1),but we didn't get factory default mode.so try reset to starting position and follow...
View ArticleRe: What is the next of obsoleted AD-FMCMOTCON1-EBZ?
Hi ACozma, Today is 18,March.I could not catch your AD-FMCMOTOCON2-EBZ on your new website.Delay?If so, when will you upload it on your web site?Thanks Kaos
View ArticleClik here to view.
Re: Blending External OSD on Adv8005
Hi Jeyasudha,I am using Blimp software for creating a UI & Adv8005 SMZ board for testing EXOSD UI.I have created the UI burned the binary file in serial flash & also merged the code in my...
View ArticleClik here to view.
Re: about ADV7441A ELPF and audio_ELPF filter capacitor
"for the ADUIDO_ELPF it is acceptable to use 8.2nF and 82nF" means the 8.2nFcapacitor in parallel wiht the 1.5k resisor + 80nF? if it change to 82nF, how to set the resistor and it's series capacitor...
View ArticleRe: AD9361: Rx Sample Streaming on Zc702 and AD-FMCOMMS2-EBZ
Michael, I cannot get the ad9361-iiostream example to work. It fails with the message "No rx dev found" I have the latest disk image, done the updates and rebuilt the tree. ZC702+FMCOMMS5
View ArticleClik here to view.
Power-Up Sequence ADV8003
Hi, From data sheet of ADV8003, during the power-up sequence of the ADV8003,1. Hold the /RESET and PDN pins low.2. Bring up the 3.3 V supplies (DVDD_IO, AVDD1, AVDD2).3. A minimum delay of 20 ms is...
View ArticleRe: [AD7795] unused IOUT2
Hi Sofy, IOUT1 and IOUT2 are used when there is a need for an excitation current in the application. According to the datasheet, when the desired output current is 1 mA, you have to configure the IO...
View ArticleRe: Exception has occurred when use adi_musbmhdrc_Stop() in CCES 1.1.0
Joe:Reply your problem.No preserve information of exception.DSP of system is BF609System is no OS.Operation for USB mass storage. I think that clear pUsbDrvData in adi_musbmhdrc_Stop() cause memory...
View ArticleRe: Network problem on BF518.
Hi Vladimir, I've some problem bringing up the on board Flash on my board, so can not test booting uImage without using eth before it's fixed. In the env ramboot, uboot do something to set up the...
View ArticleRe: Issue with ADV7280M
Hi, We were able to successfully rectify this now without the need for repeated hardware resets. Basically the issue was quite well explained in AN1337. As per AN1337 some of the MIPI CSI-2 receiver's...
View ArticleRe: [AD7795] unused IOUT2
Hello, RC,Thank you for your response!I understood that. NC is OK. Best regards,Sofy
View ArticleRe: AD5933EBZ-Problem regarding phase
HiI done with that procedure.i used 200k and 50pf capacitor.the csv are attached here. Regards Nizamudheen
View ArticleClik here to view.
Re: appropriate ADC evaluation board
Hi Jovialjha, Below is the short list of Sigma delta ADC that possibly fit to your requirement. ADI Sigma-Delta ADC portfolio range from 8bit to 24 bit resolution. And these parts are...
View ArticleDoes packing many radios in Single Chip quality it as IoT device?
Blackfin DSP have been in the past 15 years and ARM also there little more in terms of number of years. These days, IoT devices does not requires good Display or good GUI. All that it requires is good...
View ArticleAD1974 sample rate setting.
Hi,all. I'm confused the clock signal relation & register setting, MCLK,sample rate,ALRCLK,ABCLK @AD1974. In the datasheet 11page "CLOCK SIGNALS", I found the following description."In 96 kHz...
View Article