Labview source vi's for AD7173-8 eval
We're looking to take our evaluation to the next step. The eval pc software is a compiled version of a Labview gui.A link or attachment to the Labview sources would be appreciated. Thanks. knap
View ArticleRe: Design with AD8338
Hi,I am glad to help. If you have any questions on your future applications involving ADI products don't hesitate to post it here. Someone from this community will be eager to help you.By the way, may...
View ArticleRe: Using axi_ad9361_dev_if in LVDS FDD Mode
OK. Thanks. Regarding A1, it is still not clear how it is working. I assumed that my FPGA drives tx_data on the rising edge of fb_clk(fb_clk_p) and the device was capturing the data on the falling...
View ArticleRe: Can I run 2 ADAU1701 in parallel completely independent of each other ?
Thanks Dave T for teaching me this!
View ArticleNewbie needs help in setting up AD9548 eval software
Hello there, I am a newbie and I have problems using the AD9548 evaluation software. Hope someone can help me in this. So far I was able to see that the sysclk was locked and ref A is valid for use,...
View ArticleRe: Readback gain reduction of Dynamic Processor with ADAU1452
KJBob (and SteveL) - Thank you for this block! For peak metering this does a much nicer job than the k/s delay found in the default blocks for the ADAU1452. Now I'm also trying to implement some...
View ArticleClik here to view.
Re: ade7854 linux driver documentation
Hi Dan This is definitely not written by someone from ADI. I checked with my team here. Maybe someone edited the Windows driver file written by us, for Linux drivers. Please look into the origin of...
View ArticleHMC988LP3E SPI interface troubles
Hi, I've been tinkering with an HMC988LP3E prescaler along with a few other chips with the goal of making an RF frequency counter shield for the Arduino due. All has been going well except for one...
View ArticleClik here to view.
[AD9361 Filter Design Wizard] Relation between #taps and pass bandwidth
Hi all, When I designed fir filter for ad9361, I noticed that the number of taps of FIR is automatically changed by Fstop and Fpass setting.For example, when FIR configuration is set as attached...
View ArticleRe: ADV7614 Dolby/DTS TrueHD audio support.
Hi Matt, I'm from the Cypress Technology Inc. Coporation in Taiwan, we adapted the ADV7614 on our product. I'm not sure if we have licensed the source code for ADV7614. I'll contact with our local...
View ArticleRe: AD7175-2 Eval Board Schematic
Hi aym,What is your email address? I will email you the .sch file. Regards,Jarwin
View ArticleValue of Clearance and creepage
Hello Our customer will use ADuM6402.Could you give me your advice what do below difference of value of clearance and creepage mean ? VDE document downloaded on your web site says below.Clearance:...
View ArticleClik here to view.
Re: Readback gain reduction of Dynamic Processor with ADAU1452
Hello edarring, Here's another idea: Employ the-1452's unique slew volume control as a dynamics processor. This involves flopping its inputs -- placing DC into its audio input, and rectified...
View ArticleRe: AD9361 tx spectrum is always wrong, is always three spectrum
hi,till，thank you very much！the image, carrier rejection should be very small signals，suppression should be less than -40dBc，but now only -10dBc,So I should how to debug to reduce these signals?and...
View ArticleRe: ADP5090 - Super capacitor instead of battery as storage device. Can it...
Hi, The ADP5090 can't support lower SETSD voltage because the ADP5090 will turn off the power path between the SYS and BAT when the SYS voltage is lower than VSYS_TH around 1.8V. So even if you set the...
View ArticleRe: AD7767 Tsettle specification incorrect?
Hi, Olaf. Apologies for the delayed response. Are you using a 1MHz MCLK? If so, tsettling is at 2.37 ms, close to what you are seeing in scilab. Can you share your screenshots where you are measuring...
View ArticleClik here to view.
Re: Choosing supply voltage for Inamp AD8221
Hi Thejesh, For this kind of application, the commonly used supply voltage for this type of amplifier is +/-5V. This is to take advantage of the larger input voltage range. Take note that there is a...
View ArticleSimple question, whats the name of this T element and where do I find it
I was reading this note on how to use the compressor function, but it uses a T element to split the input into two. One goes to the audio channel the other the control side. I just don't know what...
View ArticleRe: AD7685
Hi, We only have an ibis model downloadable from the AD7685 product page. Regards,Karen
View ArticleRe: AD7687 Precision ADC: ADC stopped converting
Hi, Alex. Can you share your schematics and scope shots so we can look closer into this? Regards,Karen
View Article