Re: ADXL375 evaluation board's behavior at ODR=1600Hz,3200Hz
Hi NeilThank you so much for your support. Regarding "around 0 behavior", it is different from other gravity data, I think.eg. 1d=00d=0-1d=0-2d=-2Then I can understand about attached wave behavior.but...
View ArticleRe: bfrom_SpiBoot fails with failure mode depending on SPI clock speed
The issue was that the PLL had been altered from hardware defaults so the SPI clock was running too fast. Restoring VrCtl, PllCtl and PllDiv to hardware faults has fixed the problem.
View ArticleRe: Simple question, whats the name of this T element and where do I find it
Hah sorry I see it now T element, up in schematic section...
View ArticleRe: Labview source vi's for AD7173-8 eval
Hi knap,Can you give me your email address so that I can email it to you. Thanks,Jarwin
View ArticleRe: ADXL375 evaluation board's behavior at ODR=1600Hz,3200Hz
Hi Moto, I did not get your questions. The Real Time Data tab of ADXL375 just show the real time output from ADXL375, no post processing. Or say, just use xxxLSB * scale factor and using the scale...
View ArticleAXI AD9361 DAC DMA HDL
Hi, I'm trying to implement some flow control on the AD9361 DAC DMA in the HDL reference design. I have my own module that processes data that is output by the DAC DMA. Essentially, I need a way to...
View ArticleClik here to view.
use cces and sigmastudio simulat ADSP21489 problem
Hello: I use the usbi by sigmastudio simulation adsp21489 development board is no problem, use example LDR files.Now I use USBi simulation target board, I by modifying this routine LDR file in cces...
View ArticleRe: AD9361 MATLAB Model - AGC Fast Attack Mode
Moved to Linux software drivers for an answer on using MATLAB filter models.
View ArticleRe: How to control external PA and Antenna Switch when using AD9361 as...
The GPO pins are digital outputs that can be configured to monitor the status of the ENSM or serve as general-purpose logic outputs. These pins are especially useful for biasing a connected power...
View ArticleRe: AD9364 decoupling capacitor placement
In this case the closer the better. The closer the capacitors are placed the lower the parasitic inductance and resistance will be and therefore more effective the capacitors will be as bypass...
View ArticleRe: Frequency Multiplication
Hi,Can you please provide details of your application?If we say frequency multiplier, by itself, your output is the harmonic of your input frequency.mini-circuits offer some parts for it:Frequency...
View ArticleRe: How to program AD5686R Evaluation Board SPI using arduino mega 2560?
Hi Darren, I would like to do some diagnostics to the board. Please use 5.5V as your external supply and 3.3V as your external logic supply. Do not connect the SDP board.Please use this link options....
View ArticleI would like to learn to use Dsp
I m interested to learn Dsp, and I know there is a kit for dsp, but I dont know if this kit include a book and these one has a differents lessons. Is dificult to learn dsp and I need some...
View Articlesigamstudio for sharc code and param address problem
Please look at pictures, sigmastudio for sharc load the preset,version,code,param ,their address is not an absolute address.Can you tell me their absolute address, because I want to modify some...
View Articlesigmastudio for sharc linear input ploblem
Please look at pictures, I want to know if I have eight channels input, so I configure sport0, 1, 2, 3 as input, then Whether or not the linear0 corresponding sport0_DA and linear1 corresponding...
View ArticleRe: AD5933 with big errors
Hi Zone, Thanks for the clarification. For the table that you have given, Zmin = 1k and Zmax = 10k. Computing for Rfb and Rcal using the formula on Configuring the Part (page 5) of this application...
View ArticleClik here to view.
Re: Frequency Multiplication
Hi sitti,I want to multiply 50Hz Sine signal to say 5KHz signal without losing phase information. Traditional plls convert only for square, but I need for sine wave?
View ArticleClik here to view.
AD5445 single supply application
I am using AD5445 to generate output voltage 0-1.25V from a single 5V supply.I literally implemented circuit from the figure 51.Vin is supplied from ADR391 (2.5V voltage reference), the bias voltage is...
View ArticleRe: ADS simulation libraries for HMC524LC3B, HMC499LC4, HMC1040LP3CE
Thanks for the reply Kagan and Qui. But I think just the scattering parameters wont be sufficient to model the IC in ADS. Also, I want to make a PCB layout of my circuit involving these ICs using ADS....
View ArticleI would like to learn about the dsp
I m interested to learn Dsp, and I know there is a kit for dsp, but I dont know if this kit include a book and these one has a differents lessons. Is dificult to learn dsp and I need some...
View Article