CCES scripting/automation
I was recently directed to this thread by a very friendly member of the ADI's Processor Tools Support team. Since the thread is nearly 2 years old now, I would like to see if anyone out there has had...
View ArticleRe: Measurement Environment of Thermal Resistance of AD9625
Many thanks, Ian, Thanks & Regards,Akira
View ArticleADN8831 FET Requirements
Hi, I am trying to choose the MOSFETs for ADN8831, but for better efficiency I would like to use ones with lower R_DS,ON than the one suggested in AN-695. Can I use the guideline given in "External FET...
View ArticleRe: ADIS16485 to Arduino Connection?
Thanks for the link! I think I understand the orientation on the board and I have started writing a code to have the Due extract the actual measurement from the byte information. I guess I can start to...
View ArticleRe: ADV7604 RGB Full Range
Hi Adam, Did you managed to read the HDMI map register 0x53[2:0]? Thanks. Regards,Edwin
View ArticleClik here to view.
Re: Configurations for KC705 with FMCOMMS1 to run XCOMM example
Hi Dragos, I installed vivado 2014.2, rebuild the libraries and generated bit file. Also generated the .elf file using SDK from...
View ArticleRe: AD7793 internal calibration leads to seemingly random readings
Thank you! Here's the code I use to carry out the calibration: unsigned int command; command &= ~AD7793_CONF_CHAN(0xFF);command |=...
View ArticleClik here to view.
Re: Configurations for KC705 with FMCOMMS1 to run XCOMM example
Hi Dragos, I tried with serial terminal(Putty) set to baud rate 115200 and ran capture.bat but there was no activity at the Serial terminal. There was an error message as shown below: (Ran the bat...
View ArticleRe: ADV7614 Dolby/DTS TrueHD audio support.
Have you licensed our software driver source code for ADV7614? -Matt
View ArticleRe: HSC-ADC-EVALEZ+AD9656 Matlab control
Hi Said, I'm sorry for the delay. I sent an email to your registered email address. Please let me know if you don't get it. Thanks,Michael
View ArticleRe: Drivers to Communicate [ AD9269 + HSC-ADC-EVALCZ ] with third party...
Hi Touseef, As long as you're using the FPGA file distributed with VisualAnalog and using the Example_AD9640.m as a starting point, it should be possible to get both channels. You'll need to modify...
View ArticleRe: AD9129 reference design for Altera
Did you ever get a response to this? I've been looking into the same thing...
View ArticleADS simulation libraries for HMC524LC3B, HMC499LC4, HMC1040LP3CE
Hi All, This is Wasim here. For some research activity I want to use HMC524LC3B, HMC499LC4, HMC1040LP3CE. However before building the hardware I want to simulate it into Agilent Advanced...
View ArticleADuCM706x:Download firmware via RS485?
Dear Sir, I use ADuC7061 for sensor module, it works now. however, I would like to know if it is possible to download firmware via RS485?since RS485 is half depulex communication, an autodirection...
View ArticleClik here to view.
Re: Cannot get ADV7180 to display video through ADV7513
I have good news! Using much of the code Rob.Analog code, I was able to get some information to begin leaking out of the ADV7513. I connected our design to a Signal Generator and was about to capture...
View ArticleClik here to view.
Re: sigmastudio 3.11.1 support for adau1372
Hello David, Thank you for the clarification! Bob
View ArticleRe: Noisest Opamp?
Hi Steve, Ok looked through some old databooks, pretty much everything (including older FET designs) is designed to LM741 noise figures. Your source resistance tends to favour FETs anyway. Better off...
View ArticleRe: Noisest Opamp?
And regarding "For gain, I had planned to perhaps boost the gain at this stage and allow the later range adjustment stage work lower." Putting all your gain up front generally produces lower overall...
View ArticleRe: Design with AD8338
JinoL, your reply really helps me. I'll try as you said.Thank you very much and hope you have a nice day!
View Article