Re: Can I just change data in Profile register to change frequency in ad9914?
Hi,'Can I just change data in Profile register to change frequency in ad9914?Yes, you should, provided that your system clock was configured correctly esp if you are using internal PLL. Based on your...
View ArticleRe: encountered error when building uboot with the "#define CONFIG_CORE1_RUN 1"
Hi Dell, please start a new thread in the Linux forum, describe it in great details about your findings/issues (how to reproduce? in what condition? what's the error/issue looks like? software...
View ArticleClik here to view.
Re: Schematic problem using AD5421
Hi Mark, Sorry, I've taken some mistakes, here is the circuit,When I used EVAL-AD5421SDZ I disable MOSFET, but ad5421 was not become so hot... Regards,Danil
View ArticleRe: Re: Re: device class and mpeg4 enc integration issues
Hi Qian, Sorry for the delayed response, could you please contact our private support channel at www.analog.com/support so that we can investigate the issue.Once this issue got resolved, we can post...
View ArticleRe: encountered error when building uboot with the "#define CONFIG_CORE1_RUN 1"
OK, i will post it in new thread when get feedback from customer. 3Q.
View ArticleRe: AD7763 and EVAL-CED1Z
Hi, We are looking into this. We'll get back to you as soon as possible. Thanks and Best Regards,Chris
View ArticleRe: AD8488 NC pin
Hi, Satoshi. In addition to this, Analog Front End used in x-ray systems like AD8488 needs to have a very low-noise in order to avoid distorting the desired signal. So if the NC pins are left floating,...
View ArticleAD7195 Evaluation board
Hi、I have questions about AD7195 Evaluation board.I'd like to know how to adjust MCU control and LCD indication on the board.(There is a CYPRESS MCU on the board)Do you have any user documents about...
View ArticleClik here to view.
Re: AD8276
Harry,Yes the circuit works normally for several hours The part doesn't burn up in normal operation for the momentThe part fails completely and there is a little hole (see picture) but I must say...
View ArticleOP4177 Power Voltage Supply
Datasheet is not complete clear to me. Does this opamp only work with a negative voltage at v- or can it also work with 0 VDC at v- and 5 VDC at v+?
View ArticleRe: ADV7842
Our HDMI receivers (as of today) support free-run for the video signals but not the audio signals. Have you checked to see if ADI offers anything similar to ICS581? -Matt
View ArticleRe: ADV7623 Scripts
Hi Jeyasudha, Many thanks that was the information I was searching for. Regards, Mike.
View ArticleADP5090
Name some types of photovoltaic and thermoelectric energy harvesting systems(part number) which working "frendly" with ADP5090.Thanks in advanceVlad
View ArticleRe: Question about the ADV7180 with the output picture shake
Form the video it looks like the camera sourcing the ADV7180 is having a zoom problem or shaking. Do you see this effect with video generators.
View ArticleRe: OP4177 Power Voltage Supply
Fons, We get this type of question a lot with respect to op amps, but it also applies to InAmps:--- Your op amp is spec'ed on +/V, will it work single supply?? OR--- Your op amp is spec'ed on ground...
View ArticleRe: Using AD9959 to generate waveforms
Pratik, I would start with MT-085: http://www.analog.com/static/imported-files/tutorials/MT-085.pdf Then go to the main DDS page: Direct Digital Synthesis (DDS) & Modulators | RF / IF ICs |...
View ArticleRe: ADP1047 using for DC/DC
Hi james, thank You for the quick reply! No I dont have a design using ADP16xx, but I have a design using ADP1047. If you like give me your email address I will send you the schematic.I cant check the...
View ArticleRe: AD9858 divide-by-2 operation
The factory code pin settings bypasses the REF CLK divide by 2 feature. This enables multiple devices to be synchronized, if desired.The reason, in normal mode, a master reset enables the REF CLK...
View ArticleClik here to view.
Re: ADP1047 using for DC/DC
hi Eugen, You may try to adjust the internal current loop of ADP1047. For example, you can try to lower the gain of the current loop. The control loop of ADP1047 is not fast and it is not eary to tune...
View ArticleRe: ADA4870 Supply Pins
Hello,The ADA4870 has four VCC pins, two feed the output stage and two feed the rest of the amplifier. The same is true for the VEE pins. So yes all supply pins need to be connected.I hope this...
View Article