Re: How to use Inter Core Communication on bf609?
Hi, Aaronwu I cloned the new git repository but there isn't linux kernel source code in the adi-buildroot-code/linux/linux-kernel. I tryed to copy the linux-kernle sorce code to...
View ArticleRe: How to use Inter Core Communication on bf609?
Please run "git submodule update --init" as it says in http://docs.blackfin.uclinux.org/doku.php?id=buildroot:build-system:build_a_target
View ArticleRe: document of AD9257-65EBZ
Dear Kou-san, Thank you for your patience. I’ve attached the correct schematic. I’ll also have this posted to the website, but it will take a few days. The BOM and Gerber files should already be...
View ArticleRe: Does the width of lines for the output matching in PCB affect the...
Hello, I send the information about my circuit. Thanks. Best regards.
View ArticleRe: Default setup of ADV7441A
Hello Dave-san, We would like to ask to you again.Pls refer to Figure 90(p.250) and Figure 91(p.251) of ADV7441 A_HW_RevJ.pdf. ・The initial value of NVBEG [4:0] is “00101”(p.253) and “00001” are...
View ArticleRe: How to use Inter Core Communication on bf609?
Hi, Aaronwu, After run "git submodule update --init" ,it looks like that the server refused. Below is erro info for your reference. root@clouds-iwow:/work# git clone...
View ArticleRe: ADV7403 output range issue
Hello Ray, Thanks a lot for your information! Yes, their input is full range and in the past, they use ADV7402A which works well. I will let them try your recommendation. (But I see 0x71, 0x72 are for...
View ArticleRe: How to use Inter Core Communication on bf609?
Why the links is still of the old style? are you sure you have cloned the new one? Please run "git remote -v" and post the result here. For example on my side it's something like: git remote -vorigin...
View ArticleRe: document of AD9257-65EBZ
Hello Doug-san,I have confirmed the schematic from you.Thank you so much for your quick help. Best regards,Kou
View ArticleRe: AD9520 Mode0 problem with configuration
Hi kyle,Thanks for the reply. I am able to see the ouputs with 28 Mhz frequency. But i need is 24 Mhz.Thanks,Prakash BJ
View ArticleClik here to view.
Re: AD9889 EDID Read Speed
I know it's an old part, we've been shipping these for quite some time. That's why I'd like to be able to fix units in the field via a software update! We already dialed the number of retries up to...
View ArticleVisual Dsp++ 5.0 Blackfin Memory Viewer Issue
I am using Visual Dsp++ 5.0 Update 7. The hardware is a ADZS-BF537-EZLITE.I noticed strange behavior with the memory viewer. In looking at address 0x20040800 I see either 05 10 if I set the address...
View ArticleRe: This is in reference to AD-FMCOMMS2-EBZ
I would recommend expanding your search to as many manufacturers as you can find. Contacting manufacturers directly may be helpful too since they often have custom designs not available on their...
View ArticleRe: I/Q correction
The specification is stated at a frequency and I/Q correction is not uniform across the whole bandwidth.The performance will depend on the part configuration. It is recommended to measure performance...
View ArticleRe: TDD LTE possibility for AD9361
ENSM control bits are avaiable in registers 0x013 - 0x015. Control bit D2 in register 0x015 turns on both synthesizers (typically used in FDD mode).
View ArticleRe: ADuM3190/4190 Regulatory approvals
Hello Apickard, All certifications are complete. We usually don't revise a data sheet when the cert is done because the come staggering in, and there have been no updates on this part, so the...
View ArticleRe: Kernel panic - not syncing: VFS: Unable to mount root fs
You're using the ADI-2012R2-RC2 tools to build your vmImage, but I'm using the ADI-2013R1-RC1 tools. Do you think that makes a difference? Also, it looks like you compiled for BF609, not BF516, so I...
View ArticleRe: ADV212 question
When ADV212 is used in the still image compression, the input mode is the single-component input, ADV212 HIPI mode, the image width is 4096 pixels, each pixel 10bit, 128 is a line of the image frame,...
View ArticleADV7511 registers read in ZC702 of xilinx
Hi, I want to debug HDMI interface in zc702 of xilinx, and there is ADV7511 in this platform. when I want to access the registers of adv7511, there is a problem. the output of adv7511 registers is...
View ArticleRe: noise of a SDP-B board
Thank you Estibaliz Just to be sure that I have found what there is:...
View Article