Re: API/SDK for AD5667REBZ
Hi Meir, Apologies for the delay as I just recently acquired the code. It is written in Visual Basic 6. VB6 is quite old and is not compatible with Windows7 so a machine using WindowsXP will be needed...
View ArticleRe: ADV7612/ADV7511 eval repeater driver
The eval board we're using is the non-HDCP enabled one.
View ArticleAD8402 Resistance Measurement
Can I use digital multimeter to measure AD8042 resistance (rwb) or multimeter current can destroy IC?My multimeter datasheet say only: Max Open Circuit Voltage: 2.8v in Resistance Measure Thank you
View ArticleRe: Help w/ ADSP-21489... DUAL SIMD MAC 40bit Floating Point
Hi bookevg, So, if I set up the PM and DM Blocks with 48-bit widths, I can use the DAGs (pointing into these 48-bit regions) as LOAD and STORE areas for 40-bit FP Registers (PEx and PEy?). Rich
View ArticleRe: Help w/ ADSP-21489... DUAL SIMD MAC 40bit Floating Point
Hi Jithul, So, if I use the "combined" PX Universal Register, I can transfer (LOAD and/or STORE) a 40-bit FP Register with respect to the PX Universal Register which is (I guess) limited to immediate...
View ArticleRe: Wrong mode register value from AD7730
Hi, Chris, I attached AVDD and REFIN+ to DVDD (5V). Also, AGND and REFIN- to DGND. I'm using PIC but I'm directly controlling SPI signals with GPIO. As you can see the oscilloscope signals, I don't...
View ArticleClik here to view.
Re: AD831 Bias Current
Hi jdobler, we are finally replacing the part, we'll see... They have asked me though to check if the design was right, before mounting the new part. Let me ask you a few questions: 1. The LO input was...
View ArticleRe: ADSP-BF526 EZ-Board - 12-bit Data Input
Hi Craig, Just checking in to see if you've managed to find out anything about the pros/cons of using the J1 connector vs. the P3 connector above? Cheers mate, Dave
View ArticleADuM4223 Half Bridge Negative Bias
Hi RSchnell. Thanks for your quick and detailed response. -Tamil
View ArticleRe: ADV7513 Differential output appears single ended
So we have new information on the problem. 1) The cable we are using appears to have a low ohm to ground short (40 ohms) on the non-inverted HDMI signals. We went out and purchased two additional...
View Articlea finished prototype
Hello guyz! It is not a question, I just wanted to "boast" a little bit about the prototype of the ultrasonic device for the blind. It uses two boards, the top one is an adau1701 based computer (can I...
View ArticleRe: Reading the data from ADXL362 with MSP430G2230
By the way, the Arduino examples on this forum are another good place to start:http://ez.analog.com/docs/DOC-2222 Again, my colleagues may have specific examples, but I happened to be looking at these...
View ArticleRe: Fiber Optic Gyroscopes
First of all I thank you for ur reply,I am working on Fiber optic gyro, open loop and single axis phase modulated by a PZT.±4000°/sec measurement rangebandwidth: 500Hz25urad resolution
View ArticleRe: Fiber Optic Gyroscopes
ADIS16137 this seems to be a MEMs based gyro. I am looking for interferometer FOG.I actually thought of mailing you but i couldn't find ur mail ID so continued the conversation.U can mail me on...
View ArticleRe: Fiber Optic Gyroscopes
As per our calculations Input power to my FOG electronics is 40uW to 65uW (5mW is the laser diode power, 200m PM fiber spool, 1Mhz PZT freq)" A novel technique for spectral processing of a fiber optic...
View ArticleRe: JFFS2 problem
I have just changed the data cache policy from write-back to write-through. It seems this solves the problem. I need more time to test it and I have to check the performance too. But I am afraid this...
View ArticleRe: Fiber Optic Gyroscopes
Is this the paper that you are referring to? http://pubcouncil.kuniv.edu.kw/jer/files/07Nov201202070049-68_04_A%20novel.pdf
View ArticleRe: TDO constant high?
I don't know the reason but I had like problem. I tried dowload over and over again. And I did reset at different times. And wow !!! all great))
View ArticleRe: EVAL - ADAU1452MINIZ
I did everything in your email. But it appears that I am still not correct. I connected a stereo output from my PC "Headphone Jack". This went to CH0 - CH1. I used USBi to 1452. I connected a set of...
View Article