Re: Gyroscopes
Hi Jim, I understand where you are coming from. What type of angle accuracy are you looking for? Are you also considering accelerometers for pitch/roll tilt and magnetometers for yaw-angle estimates?...
View ArticleClik here to view.
Re: About ADP2164
THIS STILL NEEDS TO BE VERIFIED - STAY TUNED The Vin pin and PVIN pin can be powered from different voltages based on the abs max rating information on the datasheet.If there was a limitation on...
View ArticleClik here to view.
How to route TDM audio through multiple ADAU1701s?
Hello all, We're developing an audio mixer around a ring of ADAU1701s where each receives a TDM steam from its neighbor, adds in two analog inputs and sends the mix through to the next -1701....
View ArticleAD9650 Inverted CMOS Output
Is the AD9650 CMOS output inverted by default? By inverted I mean Gnd is 1 and DRVDD is 0. If yes, I must have missed something in the datasheet. If not, I need to figure out why my custom board with...
View ArticleRe: How to connect a 21369 EZ-KIT to ADZS-USBI2EZB and EVAL-ADUSB2EBZ
Ok, found it: SigmaStudio_for_SHARC_Users_Guide.pdf Daniel
View ArticleRe: AD620 drift
Hi dclmThe typ. zero drift of AD620A is 0.3µV/°C. Gain 660 gives 200µV/°C. Then comes the output drift typ. 5µV/°C.This 205µV/°C is amplified with 12 giving 2.5mV/°C. Over 40°C it is 100mV. Added to...
View ArticleRe: AD-FMCOMMS1-EBZ relayout issue:PIC firmware programming to a...
Dear Micheal,Can you provide a brand about a usb programmer?To update(no os driver),use a usb programmer conect to XP1(on board).then,how to do?Thanks.
View ArticleRe: AD5930 and AD5932 evaluation board software commands
Dear Sir, Sorry for the delayed reply. I tried you suggestion but it is not working. I did the following:-1. I connected the Board with Battey supply.2. I took another supply and connected it to the...
View ArticleRe: ADV7391 output drive current tolerance
Hi Eugene, We do not disclose the transfer function because we only recommend customers to use on of two RSET values, 510 or 4120 Ohms. Regards, Paul
View ArticleHow to show ADAU1442 SPDIF receiver status?
Hello. I would like to show ADAU1442 SPDIF receiver status and turn on MPx port LED.How to get info from DSP register (selfboot mode) about correct decoding of SPDIF signal?Thanks for answer.Adam
View ArticleRe: AD620 drift
Hi dclmRight, I missed that load cell was excited with +10V only. Then the negative supply doesn't matter.However normally you supply load-cells with symmetric supplies so the output signals are close...
View ArticleRe: Pink Noise Generator
Hi Byron: The White noise is truly random, for further control we do provide a similar algorithm with a seed value that you can modify to seed the white noise differently every time you turn the...
View ArticleRe: AD9467FMC connectivity with Zedboard
thanks for your reply, so i think this is the noise which u are talking about but it effects on the sine wave. . . I am using win7 and here is my UART output...
View ArticleJitter Simulation of a Simple inverter in Cadence?
I have actually dumbed down the question for a better understanding. The thing is if I run a 'pnoise' simulation for 'jitter' analysis of an inverter with a 100 MHz clock (with 50% duty cycle) at its...
View ArticleRe: AD-FMCOMMS1-EBZ REF DESIGN- MODIFY+REBUILD
Just pushed FMCOMMS1 ML605 updates - Can you try again - https://github.com/analogdevicesinc/linux/commit/a7391620d605a07fbbae2cdd7da85b1311b53660 -Michael
View ArticleRe: ADE7757arn
Hi Nabeel_shaukat I would recommend you to contact a local distributor to buy ADE7757 ICs:http://www.analog.com/salesdir/continent.asp or buy them directly from ADI’s...
View ArticleRe: Problem with the BF592 frequency settings
The problem seems to be solved. I just added the code (adapted to my settings) from the HRM page 6-38, followed by a short delay and then I used the adi_pwr_GetFreq() to get the values. The frequencies...
View ArticleRe: H.264 codec in blackfin??
Hi,Thank you. It helped a lot. I need another clarification, I can compress live BT.656 format ( Composite to daughter card ) video input to an output rate less than 3.5Mbps using ADSP-BF527 EZ-KIT...
View ArticleRe: ADAU1701 have level data feedback to MCU?
I've tried to write also an address of a cells so it looks like this: 0x01;cell address high;cell address low;parameter value high;parameter value low;3 bytes 0xFF Doesn't help. Only if in a first case...
View Article