Re: ADT7461: Confirming how remote temperature is represented
Ok, so I found Table 10 in the manual which describes how offsets are calculated using the two bytes. That seems to corroborate my understanding described above. So you can either look at it as one...
View ArticleRe: FMCOMMS1 LO Driver usage
Dustin, I thought that you are using the no-OS driver...sorry. If you want to change the LO frequency from Linux, you can write the desired frequency value to...
View ArticleRe: Eval AD7609 Artwork and Schematics
Hi, Jonathan Those files for the schematic and artwork are just what I needed. Thanks for your help,Richard Richard W Evans860 President StreetApartment 1GBrooklyn, NY 11215 On Thu, Feb 27, 2014 at...
View ArticleRe: Switching AC-coupling signals with ADG918
Hi Ingmar, Some more details. The AMR rating of -0.5V was only from DC testing. The 7dBm (yes, 0.5V rms in 50ohm system) specification was from RF CW testing with no damage was seen. Regards,Eric.
View ArticleADAU1761 multi-channel audio on Zedboard
Hi all, we are evaluating the use of an extension board with four ADAU1761 codecs in combination with a ZedBoard. The goal is to use all codecs as a single 8 channel audio device in ALSA. Currently we...
View ArticleHow to save the data in AD-FMCOMMS2-EBZ?
Is there any way to save the captured data in the SD card?
View ArticleRe: EVAL-SSM2529Z
Hello, Here are the schematic and quick start guide. Best regards,Coleman
View ArticleRe: i2C Isolation; 3kV working voltage
Hi, Thank you for your input so far. A couple of questions... You mentioned using the ADUM2400, then converting to I2C on the low side. This device takes an analog input? If I wanted to convert to I2C...
View ArticleRe: AD-FMCOMMS1-EBZ REF DESIGN- MODIFY+REBUILD
rejeesh: For Number 2: a) How do you enable the channel data from Web Interface or command line?b) Where and how can I use the raw ADC data? What signal name and what module does it exist?c)...
View ArticleRe: ADAU1761 multi-channel audio on Zedboard
Hi, The ASoC framework currently does not properly support this setup. It assumes that on a I2S bus there are only two endpoints. I.e. one master device and one slave device. There is some ongoing work...
View ArticleRe: Designing a Charge Amplifier for Triboelectric Dust Analysis
sanuzr, ADI/PMI uses the "OP" prefix. We do not make an OP129. Your schematic shows an OPA129. "OPA" is the prefix for Burr Brown, which is now part of T.I. You could consider the Analog Devices...
View ArticleRe: AD9643 and AD8366 connection in fmcomms1
Sir, yes I want to add filter between ADl5380 and AD8366 with cut off frequency 1.5 Ghz. Thank yougitanjali
View ArticleClik here to view.
Re: ADIS16210 accelerometer resolution
Original post>>In the documentation you cannot find information that accelerometer has 12 bit ADC and is converted to 16 bit. Only information you can find is that sensitivity is ~61 μg/LSB on...
View ArticleRe: ADIS16210 accelerometer resolution
Original post>... and, please, put the proper information in the documentation. It is not fair. NevadaMark>>This was mentioned in my previous reply, but to address this specifically, the...
View ArticleAD5930 Gotcha's
Given a recent 'fight' to implement a saw sweep from 2285Hz to 3000Hz over a 150ms period with a 1.544MHz clock, I figured I would share my insights for anyone else who may encounter similar issues. I...
View ArticleRe: ADV7403 CVBS-525 signal shows too much jitter
Hello Wolfgang.We too use ADI video decoders ADV7184 and ADV7403 and too we have a similar problem for NTSC 525i mode (http://ez.analog.com/message/44300#44300).Decoder output signals jitter arises,...
View Articlethe ouput power of AD9957 evaluation board
Hi, Here I have a question about the AD9957 evaluation board. How can we improve the power of the output of DAC on the board? Thanks very much!Best Regards!
View ArticleRe: ADAU1442 Input ASRC Clock problem
What is your "start pulse source" set to (in "dsp registers modes 1" tab) ?Is your serial output a master or slave?
View ArticleRe: AD620 drift
Harry, Yes 305uV. It is measured at the A/D module. It is complete analog module. Panasonic AD8VI. Used as a module in a PLC rack. I check values from HMI device. At pages 6-3 and 12-3 there is info...
View ArticleClik here to view.
Re: ADE7758 Burden Resistor Value
Dear Dlath, I am calibrating the current channels by following the steps shown in datasheet of ADE7758 page 55. As a result, the channel C is able to get quite an accurate reading compared to the...
View Article