problem with my ADIS16448 data output
hiim having a problem with my ADIS16448. some of the data im receiving doesn't make any sense.the pressure is 40 mbar, which should be around 1020 mbar. and the tempreture is much more higher.i sent...
View ArticleRe: ADSP-CM403F Unlock
Hi Prashant,The true is thatMy J-link is fault when it run "Fill with zero".But your response was very helpful.It allows me to find the problem accelerated.Thank you very much.
View ArticleOS requirement for FMCOMMS 2EBZ
Hi, when we referred the below link,http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/reference_hdl we came to know that 64-bit xilinx ISE is required to generate Xilinx netlist files....
View ArticleRe: AD9631 AUXDAC effects
My previous problem is solved. Many thanks! For another question, I set the RF transceiver in manual gain mode. I injected a single tone signal with constant power into the transceiver and then I read...
View ArticleClik here to view.
How to write UART ON BF609
Hi，everyone Using CrossCore Embedded Studio write a serial program，Using CrossCore Embedded Studio packaging good function, but debugging failure when set the baud...
View ArticleQueries about ADF4158/9's Maximum TXDATA Rate
Dear Supporters, I have read the datasheet of ADF4158/9 PLL Synthesizer IC.The Synthesizer is capable of FSK and PSK modulations as wel. In order to decide for this device, for my new design, I must...
View ArticleADFMCOMMS-1 ZedBoard Reference Design DMA Configuration
Hi,We are currently working on the reference design for ADFMCOMMS-1 ZedBoard. It seems that the DMA for ADC is configured in scatter-gather (SG) mode and polling or interrupt are not used in order to...
View ArticleRe: AD5933 source code for AVR problem
Hi Miguel, OK, I understand that. So if I do not have anywhere power-down command, I do not need to place component in standby mode. Please find attached my schematic and main part of my code. Note...
View ArticleRe: AD7763 Filter Download Question
Have the same problem with CDIV = '1' and SCR = '1', MCLK = 18,432 MHz, ICLK = 18,432 Mhz.Have anybody found any solutions? With advance thanks,Evgenyy.
View ArticleRe: About ADG3241 Level shift IC
Hi Sean, Thank you for your support.I understand it. Best regards,Tarzan
View ArticleRe: AD5933 source code for AVR problem
No, this is measured with Runk = 15 k, Rcal = 10k. Question is, why I have on Vout pin less than 2 Vp-p?
View ArticleRe: adv212_firmware_load
Hi Dave, Thanks a lot for your clarification. I think project is completed. Best regards,
View ArticleMax data rate?
According to the data sheet, the max data rate is 3.906Khz, but when I play with the Excel sheet, the max data rate is 7.8125Khz (0 for SF,AF,Notch2, Revg2 and Chop) Did I miss anything?
View ArticleRe: AD5933 source code for AVR problem
1- Based on your plot Vout > 2Vpp2- Unless you incorrect label the plots, Vout = Vin, if Rfb = 10 and Runk = 15k, Vout = 0.66Vin please, review your analog circuit. Regards
View ArticleRe: how to regenerate IP cores from core generator and rebuild the...
Did you read this? http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms1-ebz/reference_hdl
View ArticleRe: Max data rate?
from the userguide page 28 With chopping disabled, the minimum SF word allowed is 1 I'll have a look at updating the Excel sheet
View ArticleRe: SDH device driver examples
Hi, I'm unsure which examples you have already looked at, but we generally recommend the Shell_Browser example as a good starting point. You can find this example using the following path in...
View ArticleAD8333 double-ended output to single ended
Hello everyone, I am trying to demodulate a 5MHz signal using the AD8333 and need to have a low pass filter after the output, which means I will need a single ended output. On the datasheet they just...
View ArticleRe: AD5292 SDO Readback mode
Hi Mark, I will try to find a good schematic for you. In the meantime I can provide you with the details. It's two Digipots connected to a microcontroller in parallel, via SPI. 1) The micorcontroller...
View Article