ADA4930-1 Input DC Adjustment from DAC
Dear Sir/Madam,I am planning on using AD8336, ADA4930-1 and AD9681. AD8336 to ADA4930-1 is DC coupled with unipolar signal that has DC offset.The unipolar signal is connected to the non-inverting input...
View ArticleRe: VBUS error Interrupt on BF527 USB MSD Host Driver
Hello, Please provide a full description of the issue. Which software tools are you using? e.g., VisualDSP++, CrossCore Embedded Studio? Are you using the stack as is or did you make modifications?...
View ArticleEVAL-AD5360/61/62/63EBZ USB Software
I am trying to use the EVAL-AD5360/61/62/63EBZ in a .NET application (Visual Studio 2010) that uses the ADI_CYUSB_USB4.dll. The evaluation board works with the provided software. There is not too much...
View ArticleRe: AD7699, Temperature measurement
Hi Frank, The datasheet spec 283 mV may typically represent room temperature, but it could vary with temperature and due to process variartion across mutliple parts as you have noticed from the above...
View ArticleRe: AD7699, Temperature measurement
Hi Maithil, Good point. We’re doing some temperature testing, I’ll see what additional data I can gather. Regards,Frank
View ArticleRe: ADV7511 ZedBoard design with MicroBlaze instead of ARM Cortex-A9
Hi Dragos, I ran into the same problem as blong using the Microblaze library on a custom board without the I2C switch, where execution gets stuck in HAL_PlatformInit() because the switch is not on the...
View ArticleAbout ADG3241 Level shift IC
Hi there,I have a simple question about ADG3241, level shift IC.http://www.analog.com/static/imported-files/data_sheets/ADG3241.pdfI want the levelshift from 3.3V to 1.8V/2.5V.I checked out the...
View ArticleRe: ADV7511 ZedBoard design with MicroBlaze instead of ARM Cortex-A9
Reposting this here since my e-mail reply didn't get copied to the forum... I didn't use the timer interrupt at all. The ADV7511 demo seems to work without it. As far as I can tell, the timer is just...
View ArticleRe: ADV7511 ZedBoard design with MicroBlaze instead of ARM Cortex-A9
Missing fmc_iic_sw link: http://zedboard.org/sites/default/files/design/FMC_IMAGEON_Building_Video_Design_Tutorial_14_4_20130110.zip
View ArticleRe: AD9361 evaluation board with Xilinx evaluation board...
Hi, rgetz: Thank you very much for answer my questions, I think I understanding your answer and I hope you know my question's means. Best Regards, ADI_USERS
View ArticleADG2188 - I2C read protocol
I am attempting to us an I2C software package based on smbus read/write protocols. The write function works but the read function does not.I observe, using an I2C bus monitor, that an smbus read only...
View ArticleRe: AD8390 part marking
hi, Tom_G. I'm looking into this. I'll get back to you soon. regards,ahbie
View ArticleRe: Can ADV7392 do output 2Vp-p with Full-Drive Mode, without 75ohm termination?
Hello, Thank you very much. Best regards.
View ArticleRe: fully differential instrumentation amplifier
Other than looking at the conversion output , is there any any way to make sure that the spikes are settled before the conversion ? Thank you
View ArticleRe: [ADV7392] What does "Output Compliance" mean?
Hello, Thank you very much. Best regards.
View ArticleClik here to view.
Re: Can I design a variable frequency filter for a Wah Wah effect?
Hello CL91, Try using a state-variable (Q/F Input) filter as shown below. You'll find it under Miscellaneous Filters. Help for this filter block is found...
View ArticleRe: fail to generate the "spi_params.dat" file
Hi BrettG, I use 1701 in my project. Best Regards, zhou
View ArticlePlease Help，Dose ADV7401/ADV7403 support four CVBS synchronous acquisition？
Please Help，Dose ADV7401/ADV7403 support four CVBS synchronous acquisition？
View ArticleRe: AD-FMCOMMS1-EBZ Linux ML605 Setting Registers: How to?
Lars: The read/write register Web Page interface will not allow more than three hex digits? http://wiki.analog.com/_media/resources/fpga/xilinx/fmc/ad-fmcomms1-ebz/quickstart/fmcomms1_netscope_td.png...
View ArticleVBI and CGMS of ADV7392.
Hello, I have a question about VBI and CGMS of ADV7392. There is a description about VBI on datasheet page.52 as follows:"If VBI is disabled (Subaddress 0x31, Bit 4 for ED/HD; Subaddress 0x83, Bit 4...
View Article