Re: ADV7604 RGB Full Range
No it has not. I am still trying to get answers, sorry for the delay.
View ArticleRe: iio cyclic buffering
Hi Rick, I agree that 96 MiB is not large in itself - it fits perfectly in the RAM; we just have a 4 MiB limit in the kernel. I'm not sure what is the exact reason; I will try to get more info by next...
View ArticleRe: AD9548 Evaluation Board PC Driver
The AD9548 software has since been updated to work on 64-bit operating systems (versions 2.0.1 and higher). You may need to re-program the on-board EEPROM in order to associate the EVB hardware with...
View ArticleRe: ADF5355 evaluation board schematic
The evaluation board user guides are being finalized, but you can get the preliminary version here: https://ez.analog.com/message/165381
View ArticleClik here to view.
MATLAB Filter Design Wizard for AD9361
Hello All, I was designing a FIR with matlab filter design wizard v3.1, I noticed following problem.When HB1 and HB3 are set to enable and HB2 is set to bypass, the design tool dumps some errors.I...
View ArticleAD9122-M5375-EBZ Reference Design
I am having issues finding a reference design containing the AD9122-M5375-EBZ.On the website AD9122 Evaluation Board, DAC-FMC Interposer & Xilinx ML-605 Reference Design [Analog Devices Wiki]...
View ArticleClik here to view.
Re: fmcomms data rates
Lars, Can you confirm that the underflow fix has been pushed to the repo? Which branch should I be tracking? xcomms or 2014_R2?
View ArticleRe: EVAL-ADV8005-SMZ Question on enabling JT6 Header
Since you have a non-standard version of EVAL-ADV8005-SMZ, I'm going to support you offline. -Matt
View ArticleRe: HMC928LP5E application problem
One other purpose of vias under package back paddle is reducing the GND inductance, which becomes more important as frequency increases.
View ArticleNeed roughly 10ns or better ramp to drive a VCO
I'm looking for some product such as the AD9956 in an evaluation board form for quick setup. In our application we are looking to generate a ramp that can go from 0V to (8V or 10V) in less than a 10ns...
View ArticleClik here to view.
Re: AD8000 amplification
HI JinolSorry for replying late. I am attaching the block diagram of my circuit.I need an oscillator which culd be the source to drive the transmitter at 20MHz. the transmitter circuit has an AD8000...
View ArticleRe: ADD5211 FET + Rsense heating
Thanks, I suspected as much. I'll get something with lower RDSon (not sure if I should go bigger package than TO252, probably not), step the sense resistor up to 3W version, and get a bigger inductor....
View ArticleRe: Solutions for bad Load response of adp1048 interleaved pfc for a 2kw...
Can you please attach the .48r and .48b files.
View ArticleRe: ADV7611 YCbCr output format
Hi , To get YCrCb 444 out, you just need to disable the RGB_out bit (Io map, 0x02 [1] = 0) and set the output_format_sel to 0x40 as Guenter suggested. Regards,Paul
View ArticleHMC835 eval board loop filter R58
Hi, On the HMC835 evaluation board (https://www.hittite.com/content/documents/eval_pcb_schematic/hmc835lp6ge_eval_pcb_schematic.pdf) the loop filter contains a resistor R58=510R between last RC filter...
View ArticleRe: AD9122 clocking and sampling rate.
Sorry, I was wrong. Actually the behavior is the same as on your system. However, I think that this problem is already discussed on your other opened thread: https://ez.analog.com/message/176547#176547...
View ArticleClik here to view.
Re: Audio DPLL not locked on ADV7604
Hi Jean-Michel, Do you have one of our evaluation boards for ADV7604? -Matt
View ArticleRe: IIO for "packet-based" data
Paul, Great! I think I see how to proceed, then. Thanks!
View Article[ADV7611] HDMI receiver hotplug configuration
We are using ADV7611 in our board, I want to receive interrupt to driver when video source is connected to ADV7611.can you please help for ADV7611 configuration for this.
View Article