FMCOMMS5 noise floor
Hi, I am transmitting and receiving and sinewave with FMCOMMS5: the received sinewave appears at -10dBFs while the noise floor is consistently around -73dBFs (16K FFT , Fs=50MHz) or equivalently...
View ArticleRe: file missing of ADV7623 OSD tool
Hi, The file and OSD API are protected under SLA ( Software License Agreement). Could you please contact you local ADI sales representative or FAE to foollow-up and get the necessary files....
View ArticleRe: Eval. software for EVAL AD7606
Hi, I have sent a response to your private email. Regards,Karen
View Articlead9984a 1920 * 1080 resolution computer output
Debugging ad9984a in fpga when i set computer resolution is 1920*1080 Detected vsync and hsync ‘s Period is right Samples per total line 2200 Sampling Frequency (MHz) 148.5hz Total Lines per...
View ArticleRe: AD9361 Loop Filter&Charge Pump configuration
Thank Tlili,I have a question. In the file "SynthLUT_v2.zip", I don't know use column Band but If I want to config Rx freq 1710 MHz and Tx Freq 1805 MHz, what the row I will choose for config!
View ArticleRe: REF02: TEMP pin
Hello, Thank you for your reply. In data sheet of the REF02(Rev.I page3), the current of the TEPM pin is limited to 50nA.However, it has changed into the description that uses the OpAmp with low bias...
View ArticleRe: EVAL-AD7671EDZ and EVAL-CED1Z
Hi,Our evaluation software do not support continuous saving of raw data so you will need to write your own software drivers to do this. Regards,Karen
View ArticleRe: ADAU1442 with Two ADAU1701
Hello John, I am looking for Basic DSP, Dynamics Processors and ADI Algorithms (AVC, Midnight Mode, Virtual, Surround, Loudness, Dynamic Bass, LF Synth, etc.) for the ADAU145x. I am sorry, I only had...
View ArticleClik here to view.
Re: how to config Gm mixer sub table?
Thank for your answer!I have an other question, what the parameters affect the gain, bias, control. I read ADI drivers, I saw is the values fixed with any frequency? if not, we aspect the RF card which...
View ArticleRe: ADV7611 1080P50
Thank you very much. The problem have be fixed. The sony device output hdmi stream slowly, so I need a delay between configing the adv7611 and opening capture device. But I also have a problem....
View ArticleClik here to view.
Re: ADAU1452 too long selfboot time...
Hi Toino, I attempted to duplicate your issue using the ADAU1452MINIZ eval board. I could not get a 8192 FIR coefficient table to load properly, so I used four 4096-tap filters instead, as...
View ArticleRe: How do I get ADV8005 SD encoder test pattern generator to work?
Hi Paul,I have finally gotten the encoder test pattern generator to work. It required me to write to registers 0xe48c-0xe48f the values for NTSC even though the registers default to these values. Now...
View ArticleClik here to view.
Graphic EQ
Hi Sir,We are looking for solution for 8-ch audio EQ.Currently , we already controlled EQ by MCU , base on Calculating Filter Coefficients to Store in a Microcontroller But , we would like to design an...
View ArticleClik here to view.
ADV7511 configuration problem
Hi all, I met some problems in using EVAL-ADV7612-7511P(only use 7511) and AVES2 .The condition is as following：Input data: YUV422 ITU-R BT.601Type(Y8bit, C8bit, Vsync, Hsync, Clock)--HITACHI DI-SC120R...
View ArticleClik here to view.
Sigma 300 (ADAU145x) Slew Volume Rates
Slew volume controls can filter noisy control inputs and minimize clicks. Often the desired slew rate can be found by experiment. However, in some applications it would help to know the actual...
View ArticleClik here to view.
Re: ADAU1452 too long selfboot time...
Hi Bob Thanks a lot by this sanity check. Now I am facing a new problem with GPIO. I am using MP10, MP11, MP12 and MP13 as pin inputs from switches in order to mute outputs individually. After...
View Article