What is the difference between ADXL362 and ADXL363
What is the difference between ADXL362 and ADXL363?
View ArticleRe: What is the difference between ADXL362 and ADXL363
ADXL362 is the industry's lowest power consumption acceleration. It is very popular in the applications which need low power. Refer to the accelerometer, ADXL363 has the same specifications with...
View ArticleClik here to view.
AD9910 Intermittent outputs or just broken
Hello,We have designed a dual channel RF board based on the AD9910. We have manufactured 5 boards using two AD9910's on each board. Three of the five boards work perfectly. The other two boards...
View ArticleNo Linux tools ???
Is there something like ADIsimPower available based on open source tools i.e. for Linux and LibrCalc?
View Articleadum6010 dc-dc
Excuse me,I have designed a solar panel(6v/15mA) connected to adum6010,but it didn't work.why?When I use a solar panel(6v/15mA) to connect adum6010,I measured input voitage.It is down to 2v, even...
View ArticleRe: AD9361 Reference Design for the Altera Cyclone V SoC Board
Hi Robin Is there an update on this issue?Is there a timeframe for this? BR,alon
View ArticleRe: Use ADAU1452 in embedded system - remote control via SigmaStudio (TCP/IP?)
I just found this: http://wiki.analog.com/resources/tools-software/linux-software/sigmatcp In SigmaStudio I cannot connect the TCPIPADAUxxxx communication protocol to my ADAU1452. Is there a plan from...
View ArticleI search a job on the side to the study in the area of the electronics...
Hello, I want to move in next in that sews from Salzburg, there I would like to begin a work accompanying(additional) study. In parallel moreover I search a practical activity in the area of the...
View ArticleClik here to view.
Re: EVAL-AD1937AZ
Hi Dave, I have set up the loop back mode now with extenal connecting on EVB AD1937 now.thanks for your help. Br,Hans
View ArticleRe: AD-FMCOMMS3-EBZ HIL example: QPSK modulation with raised cosine filter
Hi Arnd, Thanks for posting the updated model. I too, am getting the switch between states, with a clear constellation being observed only briefly at regular intervals. I'm using a ZC706 with an...
View ArticleRe: AD9257 reset control
Hello Dougl, Thank you for your support! >4. The amount of time required for digital reset is the same, regardless of if DCS is enabled or disabled. Is this >your question? Yes. I would like to...
View ArticleRe: Questions on ADI REFERENCE DESIGNS HDL
Hi Csoml, Thank you for your clear guidance. By the way, how to pronounce Csoml? Is C here pronouced as /k/ or not? Regards, Jie 2014/11/25
View ArticleRe: using AD8067 as inverting amplifier
Hi Niloy, Sorry for the delayed response. With your noise gain less than 1.826 and a signal of 500 kHz, that makes a GBP of 913 kHz and ADA4627-1 (GBP = 19 MHz) can be appropriate for your application....
View ArticleRe: AD8529, about open-loop gain model
Hi Xueliang, Our Spice Models are modeled to work at dual supplies, this means that most of our test bench circuits are configured to test for dual supplies. Technically, the response of 12 V supply...
View ArticleADAU1452 too long selfboot time...
With two FIR blocks of 8192-taps, the booting time is about 50s !! Reading the manual, it seems that it is supposed that the E2prom starts to be accessed at low speed that it is later increased...
View ArticleRe: AD9361 Charge Pump Cal Timeout / ad9361_txrx_synth_cp_calib()
Our custom hardware makes it difficult to use your HDL exactly as is. We have some extra functional needs, like an I2C, a second SPI, a pulse generator, etc, that have been customized, and some extra...
View ArticleRe: ADAU1442 with Two ADAU1701
Hello John, Thank-you for your early reply.I did consider the ADAU1451 and the AD1938 CODEC.The ADAU1451 is a new part and the algorithm libraries are not completely available/ported yet. If AD updates...
View ArticleSample Timing
Is there any possibility in FMCOMMS2 or a related project that implements sample timing so that I can synchronize receive and transmit as in VITA 49? Thank you
View ArticleClik here to view.
Re: Some questions about ADV212
Hi Dave,After my initialization,the value of SCOM[3:0] is 7. I have read back the firmware from ADV212 memory.If I read before any parameter setting,it will be exactly the same as the original data in...
View ArticleRe: How do I get ADV8005 SD encoder test pattern generator to work?
Hi Paul,I don't have a s-video cable at the moment but when I probe the luma and chroma I see a signal coming out. I suspect it looks like the composite output (grayscale color bars). If I make...
View Article