Re: ADV7611 and ADV7610 Video format
Hello GuenterL, Thank you for your advice. Regards,
View ArticleRe: Connection of ADV7513 input pin
Hello GuenterL Thank you for advice various. Regards,
View ArticleRe: ADC7762 on board differentail amplifier
Hi, Apologies for the delay. The diff-amp does not perform well in Single-ended to differential conversion due to common mode variation. With regards to the amplitude of the input, the AD7760's...
View Article21488 Crash Issue
Dear all, I have a problem that 21488DSP crashs after it runs sometime. Please see attached picture - crash.jpg which shows a illegal PC value in PC stack.In the picture, AEC_DSP3/4/5/6 runs the same...
View ArticleRe: ADAS3023 PGIA gain config
Hi, Larry. I am looking into this. I'll get back to you soon. Regards,Karen
View ArticleHow to write a network to send and receive procedures on the bf609 ？
hi，everyone Using CCES write network to send and receive data application, But I debug errors,I doubut there is something wrong with the train of thought,Can you offer me some steps and ideas?
View ArticleRe: very low frequency preamplifier
Hi John, Thank you for your interest of using ADI products. I need more information about your applications so that I can give you the part that is best for you. Is your input signal will be coming...
View ArticleADV7623 HDMI Repeater Driver API missing ADIAPI_RxInit function?
Hi Guys. I have already written a bunch of code that directly controls the ADV7623 OSD. That piece works very well. What I didn't realize until I started hooking up different source devices is that...
View ArticleRe: A couple of questions for AD7607
Hi, Kaos. I am looking into this. I'll get back to you soon. Regards,Karen
View ArticleRe: EVAL-AD7609 Evaluation Board
Hi, The technical note for the EVAL-AD7609 which describes the operation and set up of the evaluation board is included in the software which you may download here:...
View Articlehow to use two cores for pbx
Hi, Can pbx use the two cores? if so, how to do it? Can you give us some guidance, thanks?
View ArticleClik here to view.
Re: ADIS16480 Register Writes to PAGE_ID 0x03 problems
Thanks for your reply Mark. Here is a scope capture... from top to bottom:SCLK nCSDOUTDIN (the scaling on SCLK isn't correct due to a less than stellar probe, but I confirmed that it's the correct...
View ArticleRe: BF60x SPORT pin assignment at PB_12
Hi, As the datasheet mentions SPT0_AD1 and SPT0_BTDV are multiplexed, and hence both these functionality cannot be used simultaneously.But note that SPT0_BTDV is just a status signal for Multichannel...
View ArticleRe: ADAS3023 PGIA gain config
Thanks. I just ordered the eval board to try it out. I have been trying the AD7606, and it works well, but I like having everything in one chip. The only hassle is the bipolar power supply. My signals...
View ArticleRe: bf518:lnetd echo server for udp
Hi, Sorry for the delayed response. You can refer to the examples present in VisualDSP installation (..\Blackfin\Examples\ADSP-BF518F EZ-Board\LAN). Please also refer to the LWIP documentation in...
View ArticleRe: about VisualAnalog
Hello Doug-san, I’m sorry for the delay in my reply. The output format is matched.I’ll try to use Logic canvas. Thank you. Best regards,Kou
View ArticleRe: how to use two cores for pbx
Here is a FAQ for how to use the second core, in general. http://ez.analog.com/docs/DOC-10708
View ArticleRe: IFFT Shifted Result
Hi folks, it was my twiddle coefficients. I loaded up an example coeff file that was posted here earlier and it seems to be working. The correct file is attached. I misunderstood what...
View Article