Re: adis16480 spi configuration and processing overrun
Q: The dynamic accuracy for pitch and role is 0.3 degree. Does the device still comply with this specification when it is used in linear motion?A: I am not sure that I can answer in absolute terms but...
View ArticleRe: adis16480 spi configuration and processing overrun
I have watched the video several times (thank you, by the way) and have not seen the counter increase. Am I missing something?
View ArticleRe: adis16480 spi configuration and processing overrun
With respect to your setup, I have a few comments:J1 on the EVAL-ADIS was not intended for connecting to an external processor. While it will probably be OK, there is risk of damaging the EVAL-ADIS's...
View ArticleRe: Need DC-coupled adder for ADC differential input circuit
Hi, Anik, Adding with resistors is definitely simpler, with no worry about instability due to too much capacitance on the summing nodes. This can also be tested with eval. board connections, if...
View ArticleClik here to view.
Re: the way to remove ADAU1401 pop noise when adjust the volume
Hi Miguel, it took me some time to figure the sequencer window out - never used it before.It's a great tool.Anyway, you are right - writing of a single parameter works.It makes my life easier, since I...
View ArticleRe: AD688ARWZ - Datasheet - OUTPUT VOLTAGE DRIFT
Lukas, We have the guaranteed limits for the AD688ARWZ from -40'C to +85'C but we do not have it specified or guaranteed for the narrower range of -0'C to +70'C. We do have a spec for the narrower...
View ArticleRe: Composite output with ADV7123
NTSC is defined as 1Vpp comprised of 300mV to 1000mV for the analog signal and 0 to 300mV for the negative sync pulse. Blanking interval = 0.3V. In theory if you had the right ADC signals then you...
View ArticleRe: HDL descriptions of AD9467FMC reference design
Yes i didn't modify the board, i am using external Sine wave with 100 MHz but now i want to order 250 MHz for full scale operation.I dont know the specification of temperature of soldering on board etc...
View ArticleRe: "E" model scrypt style of spice file for ADG508F
Hi Sofy, This model will work in NI Multisim as it is included in the Analog Devices version of Multisim Component Evaluator 13. Eric.
View ArticleRe: Switching in between my output signals?
Hi, It will depend on what power supplies you have available and the switch configuration that you need. But looking at the bandwidth you have quoted I think you should consider the ADG1208....
View ArticleRe: BF592 hardware use case discuss.
Hi Henry, 1] Blackfin SPI module do not supprt 3-wire protocol. There are separate MISO and MOSI lines for data transfer. But I guess, you can try to implement some part of it by connecting MISO &...
View ArticleRe: No OS ZC702 problem with _XPARAMETERS_PS_H_
Hi Dragos, I did not export the design from the same version of XPS. I didnt export it from any version of XPS. (Is there a user guide describing the procedures and versions of tools to do so?). From...
View ArticleRe: mirrored video output in ADSPBF561
Hi Asma, I guess your video source is interlaced. That is why you are seeing two frames in single frame buffer. Though I feel there is some sync issue between source and processor. There are some...
View ArticleRe: Early termination of SPI using burst mode reads in an ADIS16364
We appreciate you offering this to us. In past inquiries, we have discouraged this practice but since I had not tested this approach personally, I was hesitant to offer the same level of conviction....
View ArticleRe: updating the SD-card - re-submitted
Robin, I tried another computer (Windows) for creating the SD-card and it fails in a similar way: the process of "physdiskwrite" stops after just a couple of minutes with an error message (the error is...
View ArticleRe: Help to clarify the SPI slave description about the SPI_TWC on bf609 HRM
Hi Dell, Yes..info on p1531 is correct: the counters should not be enabled when SPI is configured as slave (although there is no hardware restriction). The info on p1518 needs to be modified. What kind...
View ArticleRe: cf_adv7511_zed - "axi_hdmi_tx_v1_00_a was not found - please see console...
Sorry for the delay, for some reason we did not get an email about this question. Did you make any progress so far? Do you still have the same issue? I already forwarded this question to someone who...
View ArticleRe: AD-FMCOMMS2-EB and ZC702 Board
Did you post this question somewhere else? Are you still looking for an answer? Charly
View ArticleClik here to view.
How to deal with these two errors in CCES?
Hi everyone, I have built an application for 21488 by imitating the sigma studio application for 21489.The modification I take is to correct the “ldf” file to fit with the 3Mbit on chip ram of...
View Article