Re: can any one help me to compute the power consumption in op amp and other...
Hi Emman, Thank you for your valuable response. I need the datas on die size and transistor count of analog devices. where i can fetch those information??
View ArticleRe: Ultra low power data collection - reading strain guage
Hi Lionell, No worries on keeping commenting. It always help because, it can be give a better understanding of the problem. I found an ADC that is differential that is supplied from 2.5V to 5.5V. The...
View ArticleRe: RMS-DC converter AD8436 single supply questions
Hi John, Glad to be of help. Also, we are encouraging our customer to mark our answers if they find it helpful or correct answer.Good luck to your work and experiments! Best regards,Emman
View ArticleRe: Product Information for Operational Amplifier
Hi Prasath, I asked about the information you're requesting, and unfortunately, you will need to course this request through your local sales representative (see this link). They will determine which...
View ArticleRe: Issue with my ad7609, busy signal o/p..
Hai Jonathan, Thank you for your response.In the attached document the output data in 2's complement in decimal form, before converting to voltage is also added.Please refer and verify. Please aslo...
View ArticleITU BT.656-4 input can't be detected by ADV7511
Hi, The video stream goes like this: DVD(YCrCb) -> ADV7180 (8-bit ITU-R BT.656 YCrCb 4:2:2 embedded sync) -> (D7~D0, set V/Hsync and DE to GND) ADV7511. The setting for ADV7180 mostly are the...
View ArticleRe: Vx and VxGND pin of AD7606
Hi, Karen Thank you for your information.I will follow your advise. Best regards,Nom
View ArticleRe: Wrong response in ADF4360-0
As you show in fig.2 , your PLL is not locked!!!So, try to recalculate your PIF (feedback filter). Use ADIsimPLL - nice program!!!Best regards!!!Alexius.
View Article5 questions: Multiple AD9361 RF PLL Sync, External LO and others
Hi1-From the documentation: The ability to synchronize RF local oscillators between multiple AD9361 is not available. Sync between multiple chips is supported only for Baseband PLL...
View ArticleRe: Determine Blackfin Derivate and Silicon rev from App
i'm also interested to knwo the chipid/dspid values for some derivates of BF-Familybut the links are obsolete, and not valid,is there any info ????
View ArticleRe: unable to mount jffs2 file system in bf548
I saw you are using "ro" in your kernel command line, I usually use "rw", I see no other apparent error at this moment. However I think the best practice at this moment is to try to boot from the...
View ArticleRe: ADV7511 Input Video Clock Delay
Assuming you are using single data rate communication for the video data, Register 0xBA (Clock Delay) allows you to adjust the position of the rising edge of the clock compared to the data. Based on...
View ArticleRe: AD9119 clocking with ADF4350
I'm curious as to why this is of interest. We recommend the 100 ohm resistor is placed across the input pins. We have characterized the part with the 100 ohm resistor in the position we recommend. Are...
View ArticleAD9361 No-OS Driver RF Bandwidth Parameters
We're evaluating the AD9361 for a WiMAX application using the No-OS software and the FMCOMMS2 eval board. For our 14 MHz RF Bandwidth application we found that the rf_rx_bandwidth_hz and...
View ArticleRe: ADV7604 STDI not locking for 1024 x 2048
That info is certainly good to know - thank you!
View ArticleADCMP580 Eval
I have used the Analog evaluation board for ADCMP580 and I'm very happy with I would like to reproduce such board in a small factor formI need to know what is the substrate used in the eval board and...
View ArticleRe: ac constant current source
Hi Anna, AD8510 is low current op-amp.Any suggestion on amplifiers for 200mA current source ? Thank you
View ArticleRe: ADP1047, PFC output voltage regulation
Hey, Since there are no flags being tripped, I believe the problem is in the power train. For a 230VAC input either your switching frequency setting of 39KHz should be changed to 70KHz for chosen L=...
View ArticleClik here to view.
Re: ADE 7880 no-load conditions
Hi Heimo1 Please find below an alternative procedure that will help you implement the no-load functionality using ADE7880 in a uniform way, even if the phases are entering no-load condition one-by-one....
View Article