Building with live sources: BuildToolChain script reports unterminated quoted...
Hi, I am having some trouble building the toolchain from live sources.When executing the followinggit clone git://git.code.sf.net/p/adi-buildroot/code sources/buildroot sources/buildrootgit clone...
View ArticleRe: Optional add-on boards about AD-FMCOMMs1
These boards are evaluation boards that are sold by the product line. If you go to the product page of each of these parts , you will see all the info you need to get your hands on these boards....
View ArticleRe: BF518 Interface testing codes
Hi, Unfortunately we are unlikely to have the bandwidth to put together any additional example more specific to your exact requirement, however the INETD already has a 'Chargen' server thread, which...
View ArticleRe: BF60x: Can some signals be configred as GPIO's after boot?
Hi Itamar, That will work. Regards,Joe
View ArticleRe: Problem with the ADCC maximum throughpu
I just stripped the original code by removing SNR calculation related functions and ran on CM403 EZ-KIT. It worked fine without any problem. I applied sine wave of 1KHz 2Vpp at J9.1 (ADC0_VIN00) and...
View ArticleADF4350 intermittent Lock Detect
I made a frequency sweep from 1.9GHz to 3.5GHz at 2.5MHz steps every 1 Second and monitored the Digital Lock Detect (DLD).I found that the DLD was intermittent and in some frequencies the synthesizer...
View ArticleADV7390 analog output aspect ratio
Hi, When they use the PAL/NTSC output , they get aspect ratio of 5:4 instead of 4:3 which causes a round target to look like egg shape.Is there a way helping them configuring the part so they will get...
View ArticleRe: Please help to estimate resources of ADSP-BF592
Hi, From the datasheet of AD9248, it looks like, the device has two PPI port interfaces (due to dual ADC). However, BF592 has single PPI port. Are you planning to multiplex the those two PPI ports...
View ArticleADE7878 awatt register
Hello For example my source connected to the eval board has 577 Watts aprox. In the AWATT register I can read "d 68354" = 683,54, if I multiple this data by 0,838 the value is 577. I don't know if I...
View ArticleClik here to view.
Re: ADXL362 : Wrong activity detection (interrupt)
Hi, I was planning to operate this kind of operation (workaround), but I was expected that no interrupt would occur during the turn-on time (which seems to me logical). Is this behavior wanted ? If...
View ArticleConfiguring the Rx channels with independent LO
It is possible to configure the Rx channels with independent LO frequency? I.e. RX1 mixer will be driven by RXPLL and and RX2 driven by the TXPLL.
View ArticleRe: my pic doesn't detect my adxl345 sometimes
Hi Jan,I have never used the ADXL345 but I am also interested in it.I am not the GURU but without a printscreen of the scope it is very difficult.The problem you describe is very strange. I cannot...
View ArticleRe: Clock transfer from digital to analog ground domain
Hi again, Any news on this one? Regards,Torje
View ArticleFMCOMMS2 ADI IIO Scope Questioins
Here some questions & notes/comments regarding the ADI IIO Scope to control the AD9361 Linux related:1. Linux provides a nice "Screen shot" applicationi from the dash home search for "screen"Q: Is...
View ArticleRe: ADAU1761: Ground connection of earphone and microphone
Thanks for your comment. I tried to modify and tested with that circuit. It works, but the current is increased a lot! Normally, current of our device is about 30mA, but it is increased to 130mA after...
View ArticleRe: AD7836 DAC driven by FPGA. FPGA powered AD7836 not yet powered. Will it...
Thanks Mr. Brenden,The explanation was clear and very helpful.With Regards,Nandakumar
View ArticleRe: AD7625 datasheet questions
Hi Frankd, The main thing to understand with this interface is that there is a quiet time where the interface cannot be clocked. This is the time where the internal registers could be updating with...
View ArticleThe difference of AD9523 and AD9523-1
Dear Sir: I am using the AD9643 + HSC ADC_EVAL (FPGA). On this AD9643 EVB, it has AD9523-1 chip need to program. However, I found in the SPIController for the HSC ADC_EVAL, the .cfg file it...
View ArticleRe: Split screen observed with PAL-M standard on composite input on ADV7181
Hi Fayaz, I am a bit surprised that you still got the issue 8 times since you forced the standard to PAL-M. Was your source only providing PAL-M all the time during your testing? What type of PAL-M...
View ArticleRe: sharc usb extender on 21469 board, documentation faulty
I have got the 8.1 wdk example license agreement: MICROSOFT LIMITED PUBLIC LICENSE version 1.1----------------------This license governs use of code marked as “sample” or “example” available on this...
View Article