ADV7181D pixel output during power up
Hello, I'd like to confirm what is pixel output status during ADV7181D powering up.As attached is power on sequence (not from ADV7181D d/s but suppose ADV7181D has the similar power on sequency), what...
View ArticleRe: fmcomms1 adc_capture and printing adc values
Thank MiT for your reply, Yes, they look exactly like that.But the thing that bothers me that I and Q keeps interchanging. And sometimes I get both I and Q same as any one of the LUTs. Please have a...
View ArticleHDMI convert CVBS
HI,everybody. Now i have a question to you that is there any IC can convert HDMI video data to PAL output(extract may allow )! such as i use ADV7611 to receive HDMI source video data ,then...
View ArticleClik here to view.
Re: Two tone sample on dma_setup or dds_setup for FMCOMMS1
Thank you Dragos,I'm successful display the two tone spectrum by setting desire f1 and f2.Now its clear for me on dds_setup function. Then I use dac_dma_setup by default code in test.c and observe the...
View ArticleRe: AD8367 - Maximum Output P1dB Point in 50Ohm configuration
I haven't looked at all of the S-parameters that you provided for the AD8367, but looking at S22 for Vgain = 2, 5, and 9 volts at about 25MHz, it appear that the output impedance is about 13 ohms. The...
View ArticleRe: AD8367 - Maximum Output P1dB Point in 50Ohm configuration
Hi Sugumar, I suggest that you convert S22 for the AD8367 to an output impedance and see what you get. When I convert S22 to an output impedance I get about 13 ohms, which seems what one would expect...
View ArticleClik here to view.
adau1452 avc block adjust freeze level and max. gain
How can I adjust the AVC block adau1452 with higher values for freeze level and gain level? The values that I can be set too low for me and I want to have a greater range avc. Or, there is also...
View ArticleRe: AD5310BRMZ Intenal VREF
Hi Kotoo-san, I think there is a typo error as AD5310 has no internal reference and that there is no Output Current Load Capability parameter in the specification table. Also, the data sheet is only 16...
View ArticleRe: What's the 5 pin headers of AD-DYNO1-EBZ on the right side?
Hi Kaos, The manufacturer part number for the encoder is ENC-A2I-1250-197-HMore info can be found on the Anaheim Automation webpage:ENC-A2I with Index - Optical Incremental Rotary Thanks,Mihai
View ArticleRe: What's the 5 pin headers of AD-DYNO1-EBZ on the right side?
Thanks MihaiI got itKaos
View ArticleAD5696R Software reset (power-on reset)
Hi,all. Please let me know if my understanding is correct. Operating the software reset, command definition is following.Is it correct ? COMMAND+DAC ADDRESS+DAC DATA+DAC DATACOMMAND:0110 DAC...
View ArticleClik here to view.
Re: Adau1452 block numeric format resource
Hello Dave, The short answer: You're having trouble finding a one-stop reference of numeric formats used by all the blocks, because there isn't one. However, the needed info is available, we...
View ArticleClik here to view.
Flash programming using VisualDSP++
Hello Friends, I am designing a board with the ADSP-BF592 chip. I understand that this chip does not have any on board flash for code. So, I am using the M25P16 flash chip. This chip I am connecting to...
View ArticleIs there available example Linux application that used AD6676 device driver?
Is there available example of Linux application that used AD6676 device driver for AD6676_EBZ demo board? Device tree and kernel example need too.
View Articlehmc-890lp5e
hi , considering discontinuation of some of your products, for some products like "hmc241Qs16" there is new replacment that is "hmc241AQs16" but for some products there is not any replacement; like...
View ArticleAD7793 FS error specification
The AD7793 Full-Scale error specification has a footnote (3) that states " Following a calibration, this error is in the order of the noise for the programmed gain and update rate selected". Is the...
View ArticleClik here to view.
Re: Can ADV7513 change pixel data clocking edge or delay video input clock...
There is no way to dealy or invert the pixel clock. The timing must comply with Firugre 2 in the hardware users guide
View ArticleRe: Is the Linux Driver of ADXRS6XX product family available?
Noted it and thanks for your help!
View ArticleRe: HMC439
Here you go. Just to clarify, this is residual or additive phase noise. Best Regards, Marty
View ArticleADG1422 switch situation when no power
Dear Guys, In a specific project we need normally closed switch that will shorted in to out while no power supplied. If you can help me i will be very happy. Regards.
View Article