Re: ADP5090 EVB question
Hi, Firstly, you need to mak sure the input power bigger than output power considering the efficiency. (Pin=Vin*Vin/4/R)Secondly, there is a OCV detecting time around 300ms when the ADP5090 can't...
View ArticleConnection from ADuCM360 to the ADT7410 via the I2C interface.
AN-1250 Rev 0, page 5 table 4 mentions .c and .h files for connection from the ADuCM360 to the ADT7410 via the I2C interface. Where to obtain these files? The same Application Note mentions on page 1...
View ArticleRe: Connection from ADuCM360 to the ADT7410 via the I2C interface.
Thank you for highlighting this - we will at least make sure you get the code here on EZ ASAP.
View ArticleInterfacing ARM and AD8403(Digital Potentiometer)
Dear sir/mam, As i am working interfacing ARM and AD8403 IC(digital potentiometer),i am measure resistance value,what i am doing is from ARM i am sending data through SPI every 20sec data i am...
View ArticleRe: Zedboard FMCOMMS2 SD Card Image
Austin: All the release files are:http://wiki.analog.com/resources/tools-software/linux-software/zynq_images -Robin
View ArticleRe: Click noise reading data from DSP
Hello Fernando, SigmaDSPs do have a "safe read" feature, allowing you to read from the DSP core rather than from RAM. This is necessary because while the RAM is busy with I2C / SPI requests,...
View ArticleClik here to view.
Re: Unable to open the .rgb files provided by Blackfin Image Processing Toolbox
Hello, I also try whatever step mention above but i got error. i try different view tool but can't open. i attach error file.how could i open .rgb file.
View ArticleClik here to view.
the problem for Vbus Error for BF526?
HI. I am using BF526 processor to develop USB OTG Host for my embeded application on VisualDSP++5.0 with update 10.0. why the bits VBUS1-0 in USB_OTG_DEV_CTLcan not be 11? when I run to...
View ArticleRe: the problem for Vbus Error for BF526?
the line is while( (*pUSB_OTG_DEV_CTL&0x0018) < 0x0010) ;//xyj 2015-02-15
View ArticleRe: ADV7511 PLL not locking
Same issue is raised to us when we kept 953 Ohms instead of 887 Ohms.
View ArticleRe: FMCOMMS5 DMA overflow handling
Hi Lars Thanks for your answers. What I meant with congestion control from the user taking of samples all the way down to the ADC was exactly that since the ADC could not be stopped (no way to handle...
View ArticleRe: CN0216: Precision Weigh Scale Design Using the AD7791 24-Bit Sigma-Delta...
Has anyone found a schematic for the Arduino variant of the CN0216 (CN0216-ARDZ)?The CD that comes with the EvKit has very little on it, and refers to the SDP variant. (A bit of reverse engineering...
View Articleav code section for 4:4:4
I have a question. Whatis the content ofSection AVforYCbCr4:4:4 24 bit interface?
View ArticleRe: code of the test pattern of AD7960?
Hi maithil,Can I ask you for info about AD7960 test generator patterns? Thanks,Lukasz
View ArticleClik here to view.
Operating the AD9252 at lowest sample rate for diagnostic purposes
Hello all, The AD9252's datasheet specifies the Minimum Clock Rate at 10MSPS. For diagnostic purposes of the system we would like to lower the sample rate to 1MSPS. Does the AD9252 work at such low...
View ArticleProblem with interfacing SPI Flash in bf609
Hi , Thanks in advance. As i was trying to interface SPI Flash [ M235P16-VMN6TP] in bf609. i am unable to write data into the flash memory, where as i was able to successfully read and write the flash...
View ArticleClik here to view.
EVAL-AD7190 Developer Board Win7 32bit USB Problem
I have been trying to get the Evaluationboard from my AD7192 ADC to work with Windows 7 32bit (and Windows 8 64bit). The board is new and the driver are from the website AD7190 Evaluation Board |...
View ArticleRe: ADIS16201 - Output data rate? - Alternatives with wide bandwidth?
The key thing that was driving this was the 2g range. The ADIS16201 sensor might provide this but the assured level of +/-1.7g. The ADXL350 provides a third axis, is smaller, lower cost and appears to...
View Article