Question for your AD-FMCOMMS1-EBZ
Dear Sir/Madam, I need your help! I just got the question from our customer.He is designing with your AD-FMCOMMS1-EBZ and Zed Board by your user guide...
View ArticleFMCOMMS5 Requirements
Hi, I am looking for a platform to develop antenna beam forming techniques. Had come across the FMCOMMS5 board, after reading thru the ADI wiki help site, I am still not certain how to...
View ArticleAD9278 dinamic range
Good afternoonWe have problems with the AD9278. Unable to use the whole dynamic range.AD9278 distorts RF signal like in attached files.Maybe our connection/programming are wrong or this is normal...
View ArticleRe: ADUC7601 single ended output
Hi Rajesh, I am moving the thread to the Analog Microcontroller ADuC7xxx community. Regards,Jonathan
View ArticleRe: AD9122 clocking and sampling rate.
Hi Jetmir, You might be lucky - exact 16 MHz should be possible without changing the VCXO of 122.88MHz.You need to get to a VCO frequency of exact 3072 MHz 122.88MHz * ( 4 * B + A) = 3072MHz | B = 6, A...
View ArticleRe: Star-connected resolver with AD2S1205
Hi Weie, I am checking on this. I'll get back to you soon. Regards,Jonathan
View ArticleClik here to view.
Re: Several questions on reading webpage of...
Hi, Can you try again? It should work now. - Lars
View ArticleGPIOs in BF706
Hi,How to configure a port pin to function as a GPIO in BF706. Why there is no "defbf70x_base.h" as there is for other BF processors like "defbf52x_base.h" where the port masks are defined. what about...
View ArticleEVAL-ADV7612-7511 Video Evaluation I2C Programming
Hi,i need I2c Programming files for this evaluation board.please share the information about these
View ArticleNetwork problem with SPI Booting ...
It's very strange for me ...I have target board with BF518 and serial flash.In serial flash there are U-Boot, uImage and rootfs (on UBIFS).If board is full booting from SPI the network not work, but if...
View ArticleSHARC 21469 Second Stage Boot Loader Question
Hello All, Attempting to code a second stage boot loader for the SHARC 21469. I have read the EE345 article and have a few questions. First, is the application selected to be loaded by the...
View ArticleAD215: is isolation voltage rating specified as continuous or transient?
Hi,AD support does not have time to answer this question but maybe you know: is isolation voltage rating of AD215 specified as continuous or transient? It is strange that all other members of the...
View ArticleRe: How to configure 2 AD9364 from Kintex?
Hi Dragos, Thank you very much for the inputs.This means, once we make the changes for external clock, we cannot change it back to use the internal clock later (it's not good to keep changing the HW...
View ArticleRe: Accuracy issues with ADC in ADuCM361
The RC filter just determines the cut-off frequency on you want to filter your signal.So the selection is up to your system requirements.The bypass of the buffer has the other effect, that the input...
View ArticleRe: Building adau1761 driver for iMX6Q-Sabrelite board
Hi, Yes. If you e.g. want to play audio on the line-out output you have to unmute the line-out output. If you want to play audio on the headphone output you have to unmute the headphone output. There...
View ArticleRe: How to configure 2 AD9364 from Kintex?
Jinoj, You can unsolder any time that capacitor and use the default configuration. Regards,Dragos
View ArticleClik here to view.
Re: Accuracy issues with ADC in ADuCM361
What's the value of your resistor divider?As specified in the data-sheet your targeted accuracy shouldn't be a problem with proper system calibration.
View ArticleRe: AD7414 - Seemingly Inaccurate Temperature Readings
Hi Lluis,Thanks both logic works independently.
View ArticleRe: ADIS16201 - Output data rate? - Alternatives with wide bandwidth?
1- For instance we have tested several accelerometers by vibrating them with an increasing frequency and the amplitude measured by the accelerometer was attenuated as the frequency increased. This...
View ArticleCan't find EE-68
Hi, I tried 30 minutes to locate EE-68 on the new website. I couldn't find it. The new website is full of hyper-deadends, the best one is the "you can contact us any time". Please have that fixed as...
View Article
