Clik here to view.
About AD6655 output , interleaved ...
About AD6655 output ...(decimated IQ mode) I know that (ChA and ChB is parallel ouput bus) and ChA/ChB' output data is series of I,Q,I,Q ... (or Q,I,Q,I ... )but ...I don't know which is correct...
View ArticleUsing PVP camera pipe and memory pipe at the same time.
Hi there,At the moment i have the canny edge detector connected to the camera pipe, taking input straight from the sensor. Later in the program, i want to use the UDS down scaler to down scale an...
View ArticleRe: ADV7619 interleaved Mode 0 to support less than 170Mhz
Thanks, David; i see and will let customer try th low resolution;
View ArticleRe: ADL5535 1PdB - 1dB Compression Point Unterstanding
Thomas, The part will reach the datasheet specified p1 dB. Either the part is damaged or there an issue with your test setup.
View ArticleRe: ADL5535 1PdB - 1dB Compression Point Unterstanding
Mehlin, The Plotted Values of S-Parameters include the test fixture. The tabular values are de-embedded S-Parameters.
View ArticleRe: Several questions on reading webpage of...
Dear Larsc, Thanks for your reply. The attached screenshot is the filesystem on Zedboard-AD-FMCOMMS3 system, where I looked around and failed to find the Linux kernel tree, could you show me more...
View ArticleMax FIR size for ADAU1452?
I'm considering using the ADAU1452 for an audio product we are designing. We have audio stream at 96KHz. What is the maximum size of FIR filter I can use with this device (for this stream)?
View ArticleClik here to view.
ADV7612 and ADV7511 Display issue
hi,I am using the ADV7612-P and ADV7511 for converter a video signal.But our board has some problems as below.Please check and recommend which register we should control.As you can see, the ICON,the...
View ArticleRe: ADE7758 not used pin
Hi Terumasa, If the ICP and ICN pins are not used then they should be tied to GND. This is good practice rather than leaving them floating. Regards,Dlath
View ArticleRe: Help with AD8302
Thanks. I did have the switchE's shown onyour pic. If the other way around, the resistances were in M ohm range. Bit there was no impact on the outputs either way. Is the power supply I attached in the...
View ArticleRe: Can I use the ADAU1701 as a balance mic input
Hi, The ADAU1701 ADC inputs are single-ended and have a sensitivity of 100 uA rms; this translates to 2 V RMS when an 18 k ohm external resistor is placed before the ADC. This value can be changed to 9...
View ArticleBF592 not reaching main after SPORT interrupt
I am setting up SPORT0 Interrupts as such: void Init_Interrupts(void){ *pSIC_IMASK0 |= IRQ_DMA2 | IRQ_DMA1; *pSIC_IAR1 |= 0xfffff23f ; register_handler(ik_ivg9, SPORT0_Tx_ISR);...
View ArticleRe: Start with AD8137
Hi, Wow, you have really gone to great lengths to figure this out, and I wish I had an easy answer for you. I am not sure what you are asking with regards to your question about an audio balanced...
View ArticleRe: fmcomms data rates
I'm glad to hear that! Is there any status information that I can get back to determine if there were any dropped samples? Basically, I'm trying to get a setup where I can benchmark sample rate, but...
View ArticleRe: AD9540 Eval Board Controlled with Matlab?
The AD9540 software was create with visual basic, so I don't have any Matlab code to forward. That said, there's a few threads on DDS engineering zone that might help. See the link below for one. The...
View ArticleRe: AD-FMCOMMS-3EBZ using only 1 Rx and 1 Tx port - does it matter which ones?
Also: The unused ports can't be "open", they must be all be terminated properly. - Robin
View ArticleClik here to view.
Re: AD-FMCOMMS6-EBZ: schematics, HDL codes and reference query
I think all have been answered by Jarret.
View ArticleRe: ADE7878 Evaluation Board - Beginner
Hi David, First of all could you clarify me on how you got the decimal value from the hexadecimal? I am not getting the same decimal value as what you got. Could you tell me which all bits I must...
View ArticleRe: PITCH TRANSPOSER
Hi,I still can not use this function because of the amplitude modulation problem.Is there any method to remove?
View Article