Clik here to view.
Re: ADV7403 power supply
I have used 10uF, 6.3V Rated capacitor to CAPC2 and CAPY1 pin, in my design. Whether it cause any issue?I have powered-On the board. I did not find any capacitor damage / fumes on the PCB. Please...
View ArticleRe: ADV7403 power sequencing
Thank you for the recommendation regarding power - on sequence. In my design I have provide 3.3V, 1.8V Analog and Digital Power Supply Simultaneously. In the datasheet, or reference manual I did not...
View ArticleEmulator ICE-100B error
Hi,I am using a customized board based on the BF-538F. I am trying to emulate the using the ICE-100B emulator but I am getting the following errorError: 0x80048015Error Description: Open Device Driver...
View ArticleClik here to view.
ADV 7403 Video Decoder Power Consumption
Hi, I am using ADV 7403 Video Decoder in my design to convert the YC(luma and chroma) Analog Input signal to Digital signal in BT .656 standard. I have powered-on my system. I have found few...
View ArticleCustom design in Zed board, FMCOMMS-EBZ, Reference design
Hi, I have downloaded vivado 2014.2 and build all the libraries and then project for ZED board and zc706 board.Now my query is how to proceed to add a custom design into my project.Any flow is there?...
View ArticleA suitable interface device for AD7762 or AD7763 VOH
HiI would like to select the suitable interface device, as level translator to 3.3V, for AD7762.An interface device's Vinh min is mostly 0.7 or 0.65 X Vdd min, I think.It is about 1.65V at vdd=2.5V.But...
View ArticleRe: IIR filter crashes on the fly
Hi Dan, Did you get your -1701 to safeload your filter coefficients? Bob
View ArticleClik here to view.
Re: ADV7619 pink lines after switching from unsupported to supported resolution
Thanks for your quick response, will try your suggestion.
View ArticleIssues with EVAL-AD7294-2SDZ Current Sensor
Hello, I have both, the EVAL-AD7294-2SDZ and the EVAL-AD7294EBZ.I got the EVAL-AD7294-2SDZ because it allows me to interface to the I2C without cutting traces.However, I don't seem to get the Current...
View ArticleClik here to view.
Communication Problems with AD7734
Hello Every body.Im trying since 3 Days to get a AD7734 working. ill describe the Problem and hope some one can help. The AD7734 is connected with an atmega16 from atmel. REFIN(+), BIASHI and BIAS0 to...
View ArticleADF7023 Reed Solomon (RS) Firmware Issue
Hello, I am trying to get the Firmware rom_ram_7023_2_2_RS_AES.dat on a ADF7023 to work. I am facing the following issues: Config: Packet starting at 0x10, TX and RX on different modules (one only RX,...
View ArticleHigh Spec Automotive Gyroscope
HiI am a student looking for some basic information. I need to discuss chassis roll over sensors in my thesis.I have looked at the ADXRS300. Is this a chassis roll over gyro that is currently used by...
View ArticleRe: An error message appeared and said " *** ERROR *** The circuit is too...
Hi Lucav. Thanks for your answer.I understoof perfectly.I really appriciate your support.dona
View ArticleRe: Calibrating AD5933 with Arduino
Hi there, I would don't quite understand solution in relation to code. Would like to run the AD5933 with arduino and please post modified code! Thank again. Jean
View ArticleRe: Calibrating AD5933 with Arduino
i can run the code on the arduno and get temperature, but flag always comes back 0 when it calls runsweep, so I don't think it is accessing the right byte. How do you mask D11-D10?
View ArticleRe: ADL5801 Quiescent Current
Hi,bkamak Thank you for your reply. I'm trying to use the ADL5801 in low consumption mode.In order to examine the maximum current capacity of the DC / DC converter, I want to know the measure of the...
View ArticleClik here to view.
PIXC and EPPI 's RGBFMTEN can be used together ?
Hi,Board with a RGB666 LCD screen.When not in use PIXC, images can be displayed properly .Such a data stream is：MEM(RGB888)->DMA->EPPI-->LCD(RGB666)EPPI and DMA configuration is as follows...
View ArticleRe: AD9102: help with /TRIGGER programming
Hi Tim - I'll look at this in the lab tomorrow with your regval file. Thanks,Larry
View ArticleRe: PVP Convolution Instructions
Hey there,If you go to:C:\Analog Devices\ADSP-BF609_Evaluation_Board-Rel1.1.0\BF609_EZ-Board\Blackfin\Examples\drivers\pvp(providing you have the BF609 support package downloaded)You can find multiple...
View ArticleRe: VAT demo: how to seperate ObjectDetection?
Hello, That OSStart has something to do with uC. I think you can get a solid understanding if you go into file-io.c/vat_demo.c and follow that through (Not in debug mode, just scroll through/read code...
View Article