Could ADV7403 support YPBPR/RGB 1080P30 component input?
Hi,We want to use ADV7403 to design a video system with YPbPr/RGB input.Could it support to 1080P30 analog component input? Another question is could ADV7393 support to 1080P30 output? We also want to...
View ArticleClik here to view.
Re: Could ADV7403 support YPBPR/RGB 1080P30 component input?
Correct the Another question is could ADV7393 support to 1080P30 output? We also want to develop a product with this encoder. In datasheet, there's some description about standards supported. Does it...
View ArticleADSP-TS101 Booting Option
Dear Analog Devices Team, We are using ADSP-TS101SAB1Z000 in one of our design, We have made strap pin /BMS as "0" so that the system boots from EPROM/Flash immediately after reset. In the ADSP-TS101...
View ArticleClik here to view.
Re: ADAV803 problems
Hello Dave The workaround seems to be a good solution but i wish to know if there is a better one. Signal is braking constantly and periodicaly. I am switching it on and off for a longer and longer...
View ArticleAD9467EBZ ref design
Hello, I hope these queries haven't been answered in some other thread (I tried searching for them but couldn't find any).1) The custom peripheral added to the AXI bus in XPS is axi_adc_1c_0. This...
View ArticleRe: Interfacing ADAU1701 with AD1955
Apologies for the bump. Does there need to be a level shifter from the ADAU1701's 3.3V to the AD1955's 5V when using this buffer? Does the supply voltage of the buffer matter here?
View ArticleRe: AD9915 parallel write timing
Thanks for the clarification. Regarding IO_UPDATE and SYNC_CLK: I understand that one can write in parallel mode multiple registers before doing the IO_UPDATE, so the IO_UPDATE timing does not have to...
View ArticleClik here to view.
Re: ADAU1761 at non-audio sample rate (i.e. 51200)
Hello, Yes this is permissible. The data sheet allows for a MCLK period as short as 37 nS in 512 x fs mode. This corresponds to MCLK as high as 27 MHz, or a sample rate of 52.7 KHz. Thus,...
View ArticleADV7188
HelloI would like to ask on the above ADV7188 decoder.I think I see on its datasheet (Rev 0 from 2005) a contrediction between Table 9 and Table 101at the definition of INSEL[3:0] Register about values...
View ArticleClik here to view.
Re: SRC AD1895, how much difference between input and output sample rate does...
Thanks for your reply.I understood that it is difficult to show the specific values.Under normal conditions, small jitters may occur, but they could be rejected, I think.But when we change the sample...
View ArticleRe: CN0251 unstable voltage issue
In addition to,the sscilloscope in the report mean "CN0269" demo kit.
View ArticleRe: [ADV8005] the I2C address of ADV8005 generated by Blimp
Hi Joel Ding, Through Blimp , we cannot choose the I2C address. If it is conflicting with others you can use 0x18 also.For IO map, If ALSB pin of ADV8005 is set to low , you can use the I2C address as...
View ArticleRe: How to load u-boot.ldr in BF609-Finboard?In windows,and the board isn’t...
Thank you.Yesterday I try to change my baudrate from 11200 to 57600,and luckily it works. The u-boot which i used is u-boot-bf609-ezkit-spi-2012RC2-RC3.ldr. The u-boot-bf609-ezkit-spi-2014R1.ldr...
View ArticleAD9970 and CCD in "waiting mode" - problem
Hello! I use AD9970 in scientific CCD camera design. It works fine in "continuous" mode, when the camera captures images continuously frame by frame. But we need the camera to work also in "waiting...
View ArticleRe: ADAU1761 with ground-centered headphone configuration
Hello Dave, Thank you for your interest. It was not possible to suppress the pops significantly by increasing the capacitor value on the CM (22µF) and using of highly resistive headphones (70Ω).Even...
View ArticleRe: [ADV8005] the I2C address of ADV8005 generated by Blimp
Hi Poornima, Yes. I understand ADV8005 can be used on I2C bus either at address 0x18 or 0x1A by setting ALSA pin to low or high. However Blimp does not grant this freedom. In 1.81RC1 source code, just...
View ArticleRe: I want to find detailed description of all the ADM1066 register.
Hi Tracy, The steps you've described is not entirely clear to me. Are you trying to decode/understand someone-else's code? Could you please clarify what do you mean by write a byte 0xAA?The SMBus...
View ArticleRe: Is there any way to get email alerts when specific questions are posted...
Hi Lisa, If I set follow on that group, then I will get mail for all discussions right? Can we set any filter in that group and get email only on Particular discussions ? Best Regards,Jeyasudha.M
View ArticleClik here to view.
About AD620 Make vs. Buy Error Budget
Hi there, I have a question about AD620's Table 4.http://www.analog.com/static/imported-files/data_sheets/AD620.pdfAbout the Homebrew circut caluculation, where does Gain Nonliniarity spec"40ppm" come...
View Article